I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello
I am developing a firmware for nrf52832 using buttons like if I continuosly press my button for 6 seconds it will go to active mode from sleep mode and have been using...
Dear sir,
I have a light sensor connected to P0.04/AIN2 on 52820. How can i get the change of voltage?
I use the COMP, and has enabled COMP_ENABLED in sdk_config.h, compiled...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
We have a standalone application with no SDK integration. We would like to have the possibility to do OTA Updates via BLE and maybe introduce BLE support later on.
So for...
Hi,
I am trying to run IPSP example from nRF Connect SDK 1.4.2 IPSP sample (v1.4.2\zephyr\samples\bluetooth\ipsp). The "ping6 -I bt0 ff02::1" command is working fine but...
Hi, I am using the nRF52840 DevBoard with SDK 16.0 and Mesh SDK 4.1 and am building on the light_switch_client example.
I am trying to change the publication address by...
Hi,
I'm using nrf52 with s132(v17.0.0).
When I connect nrf52 with my phone, there is error like this picture.
And, the code is
When the buffer is filled, then...
Hello.
When I use NRF_SAADC_INPUT_AIN7 in SAADC, I get an error in calling nrf_drv_saadc_channel_init(). Looking at nrfx_saadc_channel_init() in nrfx_saadc.c, it seems to...
Hi,
In order to determine signal strength we parse the AT+CESQ response and regularly get +CESQ: 99,99,255,255,255,255 (the final number being the strength), but the connection...
Hi,
1、If I want to devlop zigbee with nRF52840, whether the only one sdk series is `nRF5_SDK_for_Thread_and_Zigbee_xxx` ?
2、Can BLE coexists with Zigbee in a nRF52840...
Hi,
I am using a nRF52832 module to receive some data from another nRF52832, which is sending the digitalized data to the receiver. My receiver consists of a nRF52832 module...
Hi guys,
I am trying to add some BLE OTA functions to my NRF52833 running Zigbee. I have looked into the examples in the SDK, and i can see that there is an example for...
1. Please provide the latest nRF52810-QCAA-R rohs and reach. 2. I did not find the latest nRF52810-QCAA-R rohs and reach at info. 3. The picture shown is older for the customer...
