I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
When I used nrF52832 mouse application, the SDK version was 15.3. When I connected to MacOS, I had to make several attempts to connect. Can you tell me why?
Thank you very...
Our nRF52832-based board is powered by a coin cell battery, and spikes in current can cause the voltage to drop. This is okay early in the battery's discharge curve, but as...
The communication between the UART peripheral and the nrf52840 works fine until some device connects to the nrf device via BLE. Using a digital logic analyzer I'm able to...
hello
now we want to use nrf52840 qspi interface to connect with fpga. we have a question:whether nrf52840 could be used as qspi slave, and fpga used as master?
if it...
Hello everyone,
I am a beginner with BLE and the nRF52, so I apologize in advance if this question is pretty simplistic. Basically, I am trying to achieve the most data...
Hi, while flashing devices in production testing our customer ran into the following problem. modemFW_flash.py got stuck in an infinite loop, making no progess but consuming...
HI,
Just like discription in the ttitle. I cannot find functions (sd_ble_gap_address_set() and sd_ble_gap_address_get()) in ble_gap.h.
How can I set device address?
...
I apologize if this has been asked in a different way but I have come across several older threads that seem outdated and was hoping for the new "best practices" for the current...
Hi,I have a problem.Sometimes the program will execute to 0x08c8 during simulation on NRF52832，SDK15.2.0，Mesh3.2.I checked the map file, which is part of Softdevice.So I think...
Hello
Using PCA10040 dev board,
Building with SDK 16, & S112 - using ses
Running ..\examples\dfu\secure_bootloader\pca10040_uart_debug
Using nrfutil to download...
When running the "nrfjprog --recover --log" command, on a Windows 10 pc in CMD, this is the output that I get. I am unsure what steps I need to take from here.
Any help...
Hi,
In my application I have a requirement to send notifications to mobile on triggering particular Interrupts as well as particular events.I have created a customised notification...
Supported tx_power values: -40dBm, -20dBm, -16dBm, -12dBm, -8dBm, -4dBm, 0dBm, +3dBm and +4dBm.
What is difference in the behavior of nrf 52832 chip for these different...
We're developing Bluetooth tags that we would like to operate at both 1Mbps and coded (long range). From what I've read and seen from the Nordic testing, specifically "Testing...
