Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
Hi Nordic,
As far as I can see, there is BLE_NUS_CONFIG_LOG_ENABLED defined for ble_nus in sdk_config.h. However, I cannot find the similar BLE_NUS_C_CONFIG_LOG_ENABLED...
Hi, can we use a manufacturer name of our own for the usb in nrf52840?
We know that we can still use the Nordic Semiconductor's usb vendor in a commercial product.
Best...
Hi, Can I use nRF24LE1-F16Q24-DK without nRFgo Starter Kit? If yes please suggest me programmer to program nRF24LE1 by Keil IDE. by referring documentation I found its support...
Hi
SDK v15.2.0 SD 6.1.1
I have managed to send out "Connectable, Non-Scannable" extended adverts with some AD packets as payload. On a frontline sniffer as per the file...
I am developing a HID keyboard based on an nRF51822.
The firmware source available here:
https://github.com/martonmiklos/ble_keyboard_fw
(It is based on the ble_sdk_app_hids_mouse...
Hello,
i'am trying to control the pwm Idle State Level.
between my Sequence's (1sek) the PIN stays High But i need it low.
I try to set the GPIO Out Register, but...
Hello,
I am working on a simple Bluetooth mesh example setup with the following configurations:
nRF52832 DK: light switch server, subscribed to group 0xC000
nRF52840...
We have a mobile app on iPhone and Android, the NRF52 advertises every 3 seconds. The app can discover the NRF52 quickly but it takes a long time to connect. The iPhone is...
Hi,
I am developing a system that will read from a sensor that uses I2C and then transmit this to a "master" using ANT+ or BTLE (this isn't decided yet)
For the prototyping...
Hello,
Where can I find the pre-built binaries for the below Provisioning options :
1.OOB (Public Key) and Authentication - Input
2.OOB (Public Key) and Authentication...
Hello.
I have an nRF51822 chip and I'm trying to figure out how the whole nRF5 sdk works.
I am using the Segger Embedded Studio.
I downloaded the last nRF5 SDK v15.3...
Hi!
I'm trying to use the AWS-FOTA sample, I flashed the sample onto the board and it connected to the AWS account successfully, but when I try to add the update.bin file...
Hi. The main loop of my app is mostly doing SPI communication to a GPS receiver. I'd like it to do that every second or so and spend the rest of the time in system on but...
Is it possible to configure the ACL to protect the UICR registers?
If so, would this have any impact on the SoftDevice or other nRF52840 peripherals? I.E does the SoftDevice...