i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi,
I have an application (central mode) which regularly connects to a number of clients, read characteristics and then disconnects again.
Whenever there is an unintended...
I'm have nRF52 DK, wish use nrfutil (v4.0.0) to update target firmware. Works fine when using -n "Target Name", but I get a "Device not found" when trying to use parameter...
I have a custom designed PCB that has the nRF52832 (taiyo yuden EYSHCNZWZ) on board.
When I flash the board using pogo pins and the jlink (debug out) from a nRF52DK, everything...
Hi,
I am using the nRF51 dongle to connect and subscribe to specific characteristic and i am getting notification correctly but when subscribing to another notification...
Hello,
are there any plans / work in progress to support 802.15.4 radio in mbedOS?
Currently nRF52840-DK is a supported target platform but if you want to work with
...
Hi all,
I am using power profiler kit to measure as mentioned below screenshot.
I want to achieve current number as mentioned in Nordic product specification as" IOFF_RAMOFF_RESET...
Hi,
I'm using nRF52832 with IAR and SDK V15, S132.
I incorporated the peer manager in the uart serial profile example.
I assume, since I have 3 pages (inc. GC) set in...
I have a device that uses peer manager to pair using a key. I have noticed that the device will connect to an app and stay connected even if the pairing procedure is not completed...
Hello,
I am using the nRF51 dongle, SDK v10 and s310.
I want to use the dongle as a ANT+ receiver and BLE client to connect to multiple BLE peripherals. I have looked...
I am once again frustrated with nRF5 API's. Getting a value from analog input pin is that simple with Arduino API's:
int sensorValue = analogRead(A0);
That's all you...
I'm using an IMU sensor and transferring data over Bluetooth to Android device. The data sampling at 400hz, and I'm sending 6 packets per connection, each packet 20bytes....
Hello!
I am using the PORT event interupt sense handler to wake up the device from various pin interupts. We have in total 6 pins that need to do that.
This works fine...
Hi,
In my project, I am interfacing various modules (UART over ble, ADC, SPI, I2C) on nRF52840-Preview-DK board. I use IAR Embedded Workbench with nRF5_SDK_15.2 for code...
Need assistance/recommendations for working with smaller pin pitch (150 micron) mounting holes for the new nRF52480 chipset. Our current contract manufacturing supplier for...
Hello I noticed the problem with nRF51 DK and ble_uart app.
1. The nRF51 DK is connected to the Terminal
2. Connect to the nRF via "nRF Connect" application on Android...
