I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hello!
I have very strange issue when same firmware works fine if it is flashed using segger debugger and randomly fails (with device restart) when it is flashed using BLE...
We have been using the Nordic PPK to optimise the power usage of our nRF52840 based application - very useful tool.
However, our application changes modes over time (e.g...
I have a local ipv4 network with a Mac laptop. There is a Raspberry Pi Thread border router connected to the network. There is an nRF52840 running the Thread CLI example....
Hello ! I have an issue that is making me crazy so far
I am trying to connect to NRF52832 devices with my smartphone. They have to collect data from sensors inside smart...
Greetings,
I'm getting some trouble trying to fix a warning. I'm running the exemple ble_app_uart_c from the folder ble_central. When I run it, I keep getting the warning...
Hi,
From the pwm driver, there is a function that use sequence that control the dimming while not blocking other task in the program, may i ask if there are any function...
Hi,
is it possible to use the GPIOTE in OpenDrain mode?
I want to use the Timer with an GPIO. So i use GPIOTE with PPI connected to the Timer. This works. But my Pin Configuration...
Dear Nordic Team,
I am trying to use the MWU to safeguard RAM of my application. Since softdevice also use this unit, I wanted to understand that where I can write the...
Hi!
I can able to read values from BMP180 but I am getting random values.It shows temperature values in some 200 range like that.How to get proper temperature value??? ...
board: custom board nrf52840
IDE: keil5
SoftDevices: s140 V6.0.0
SDK: 15.0.0
hi, I want to decrease my consumption of my board.
Now, i enable the SoftDevices and...
When I am using peripheral/cli example and debugging through RRT, I see following outcome when I am typing commands.
OUTPUT :
Command Line Interface example started...
Hi,
I am working on light switch example. I am broadcasting a message from client to servers using the API access_model_publish() with the opcode SIMPLE_ON_OFF_OPCODE_SET_UNRELIABLE...
Hi:
When I tested the DFU function of BLE, the upgrade was unsuccessful, and the APP print log prompt appeared to be a CRC check error.
The SDK version I am using is nRF5_SDK_15...
I reference demo1 of PWM driver example in SDK15.2.0, I make myself PWM driver. the official demo1 use pin17-20 as PWM channal1-channel4, but I use Pin9-P12, I modify the...
