I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I have a Redbear BLENDv2 and want to program it with Keil. I am new to both Nordik SDK and Keil. Any help how to get to the example or open the example projects
Hello,
My question is about the case when initiator device attempting to restart encryprion with previously bonded responding device that lost the bond context.
As usual...
Hello,
I am trying to interface bme 280 with nrf52. I am using sdk12.2.2 and referring code twi_sensor.
I am able to initialize the I2C drivers and I can read the chip...
Hi,
My name is Bruno, and I am working with a Bluetooth module from u-blox(NINA B112-00B) which contains a nordicSemi board nRF52832 with a Cortex M4 processor. I'm getting...
Hello,
I am trying to combine Softdevice, bootloader, and Application hex files in single hex file.
Currently using s130, SDK11, nrf51822.
I combined files using this...
1, run NRF52832\nRF5_SDK_13.0.0_04a0bfd\examples\peripheral\uart, uarte_irq_handler can get irq when receive a byte.
2, run NRF52832\nRF5_SDK_13.0.0_04a0bfd\examples\proprietary_rf...
Hi,
I made an experiment and the result doesn't correspond with my view on how the BLE communication "connection" mechanism works.
I have an app running on the nRF52832...
Hello All
I am using following SDK version 12.2.0.i am facing some problem in some example project
could you please help me
If i flash the pre compiled hex file...
I held the boot button to enter bootloader mode, and accidentally dropped a hex file into the drive that popped up. Now I can no longer get a comm port to show up on the PC...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
(nRF51822, but also concerned with nRF52832, SD130, SDK 12.1)
I'm trying to write/erase flash from a bluetooth event handler. As it's been outlined in other questions,...
Hi,
I am just updating my application from SDK13.0.0 to SDK14.0.0.
2 Services are in use: DIS and NUS. To advertise that, I made use of the scan response functionality...
Hi,
I have the D52QD2M4IA-A chip (from dynastream) that has inside nrf52832 chip. It has also builtin an onboard LIS2DH accelerometer. However when I am trying to connect...
Hi,
I am working on nrf52832. I am preparing application where I need to handle central connection with two peripherals and keep tracking time. I know that softdevice has...
The data sheet recommends that both the TWI clock and data lines use pull ups and the GPIOs should be set to S0D1, essentially open collector drive. I can see the need for...
