hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Is there a way to change the Thread SDK example program (\examples\thread\ncp\ftd\uart) baud from 115200 to a higher 460800? If so, what steps are needed to make this change...
With SDK For Mesh v5.0.0 the replay cache is saved to flash using MESH_CONFIG_STRATEGY_ON_POWER_DOWN. In mesh_config_load() a check is made to ensure that there is enough...
Hi,
I'm working on porting BG95 to nrf52 sdk, it'd be a lot helpful if I can get a head start with some open source implementation(AT parser libraries, drivers porting etc...
Hi,
In the Product Specification for nrf52840 it´s written that setting CONFIG (0x50C) register to Pause (0) would pause the watchdog while the cpu is halted by a debugger...
nrf52840 with SDK15
I am trying to update 3 characteristics if the correct value is written to an authenticated read write characteristic. Actually all of my characteristics...
I'm trying to create a simple point to point link using the nRF24L01+ with a new non-arduino microcomputer. I've searched the internet for example Python programs but only...
Hi,
I would like to double check with you if 9-pin cortex-M adapter board for Jlink can be used and connected to PPK P21 connector : https://www.segger.com/products/debug...
Hi Team,
We are using the nRF52840 DK for one of our project, as part of that we are using internal flash one of the sector with start address of 0xfc000.
We have written...
Hello, we are having a low occurrence issue when attempting to write some data in NVM using fstorage.
We are using a nRF52832 as a BLE peripheral using SDK15.2.0 and SoftDevice...
Nordic colleagues,
We just received our nRF 52840 DK and are attempting to install the nRF Sniffer application to use with Wireshark. We were able to program the DK with...
Are there any plans to expose a raw packet interface for the nrf9160? And ideally forwarded via an async serial port, perhaps as an option for the SLM application? i.e. without...
Hello,
I have a problem of reading GPS options for "NRF_SO_GNSS_POWER_SAVE_MODE"
This is the code:
I always get -1, and errno value 22. This function works for ...
Problems encountered in nrf51822 software development: When burning the program to the microcontroller, I used the Bluetooth serial port service to send the collected adc...
I'm working on a prototype currently using the nRF52840 dongle. I've used the ble_app_blinky as a basic, and added some custom code to it. The goal is to use BLE in the end...
Hello everyone,
My empte memory is displayed as EE instead of FF after i cleared the memory.
I use commandpromt to check memory:
nrfjprog --qspicustominit --memrd...
