Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi,
I am trying to develop an application for Thingy:91, which would allow me getting data from BLE and sending it to the cloud with LTE. I am working on NCS 1.3.0.
Of...
I just tested with the example project, "ble_app_uart" using SDK, "nRF5SDK17009d13099.zip" on nRF52DK (labelled with PCA10040 1.2.4 2018.23) board on Segger embedded studio...
Hi ,
i am trying to interface a WINBOND W25Q64JV flash module with NRF52,i can able to read device id,status register success fully.
i wrote the data in particular address...
Hi,
I'm using nRF52840 DK as a central. Our project is based on ble_app_uart_c example. There is filter for UUID only during scan.
I noticed, that for conection establishing...
I'm using the nrfjprog command "nrfjprog -f nrf52 --reset". This sometimes causes my custom board to hang. I dont think it is able to boot at all, I do not see any uart output...
I would like to ask Nordic to create an example of an Android background service that can detect a device advertising.
Android imposes background execution limits which...
I am using nRF52840, SDK 16 + s140 with segger embedded studio.
I have already added NUS service to my application by taking reference to ble_app_uart example. I want to...
I need to somehow connect 10 i2c devices to nrf52, to do that I need 5 i2c peripherals, but nrf52 has only 2.
I see different options:
1) Use multiplexer. Probably a good...
Hello, support team.
I try to use nRF Connect v3.4.2 on Ubuntu 16.04.6, VMware.
But there is no response after executing specific application eg. Bluetooth low energy...
Hello everyone,
I have problem with a code for reading BME680. Here is my code the values display are wrong and never change.
Thank you for your time. I used this Library...
When adding the DK to my nRF cloud account, I get the following error message: " There was an error adding your device: nRFCode 40102: Ownership code [HWID] is invalid for...
nRF52840, SDK v16.0.0 SD140v7.0.1
Our electrical engineers gave us a hard ATT_MTU limit of 65 bytes, so as to keep the peak current low on the battery for our ultra-low...
Hi,
I'm running into a problem where a TWIM TX call gets stuck internally waiting on the NRF_TWIM_EVENT_STOPPED event. It never breaks out of this while loop in the twim_xfer...
