I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I'm trying to get the most performance per mA out of my nRF52, for test purposes I've used the nrfx libraries to communicate to the peripherals but I want to make my own....
Dear Nordic
my SOFT DFU fail when I init the WDT, but I have feeddog and disable the WDT, like below:
static bool app_shutdown_handler(nrf_pwr_mgmt_evt_t event) { switch...
When access_model_subscription_list_dealloc() is called the entry is memset to 0 and the ACCESS_INTERNAL_STATE_INVALIDATED flag is set.
The function access_model_subscription_list_alloc...
Hi all,
I have a nRF52 DK (PCA10040 V1.2.1), and I want to learn how to develop on macOS.
I read from this link , and I got following information.
But I cannot know...
Hi,
I use The Texas Instrument software "SmartRF Packet Sniffer Bluetooth Low Energy" to catch the communication between my peripheral build with nRF52832 and Zwift (software...
Hello
I am trying to configure your TWIS (not using the SDK) and have run into the problem that the TWI master cannot pull the SDA and SCL line low. So, the communication...
52832's PDM function. After initialization, call the nrf_pdm_enable function, and then call the nrfx_pdm_start function. NRFX_PDM_ENABLED is set to 1. But the clock pin always...
I am evaluating the NRF52810 (using the PCA10040 dev kit), and I am having a hard time getting down to the described power consumption of the chips. I am using the power profiler...
i have done ble_app_template writing values from nrf app connect, in that i have send only integer values from nrf app connect
now i want to write float values from nrf...
Hello,
I have enabled the watchdog timer in nrf52810 with below code
NRF_WDT->CONFIG = (WDT_CONFIG_HALT_Pause << WDT_CONFIG_HALT_Pos) | ( WDT_CONFIG_SLEEP_Pause << WDT_CONFIG_SLEEP_Pos...
Hi,
I have some problem with experimental_lpn project from sdk_for_mesh. (Today I tried both sdk 3.2 and 4.0)
Code loads and starts ok on my PCA10040.
After first steps...
I use NRF52840 Evaluation Kit.
I want to use TIMER with nrf_drv_timer. However, I get an error and cannot use it. The error is the following part of "nrfx_timer.h".
...
