Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
We have a product that uses nrf51422_CE_AA, Revision 3, 256KB ROM, 16KB RAM, PCA10028, SDK 8.0.0, S110. We are now in the stage of power optimization. Therefore we bought...
Hello,
I have used the NORDIC power calculator to calculate the current consumption for different advertising intervals.
Adverting interval (ms) Current (mA) calculated...
Hello is a starter developer
I used the nrf51822 chip on the pcb board and downloaded the example code but it did not work.
When I checked the 16mhz external crystal on...
Hi all,
I am a bit confused about the use of SOFTDEVICE_HANDLER_APPSH_INIT and similarly APP_TIMER_APPSH_INIT. I've not been able to find anything in the documentation...
nrf52840, S140.
So for the past 1 or 2 weeks I have been fighting with this problem :
Now it turned out that the connection handle may actually be INVALID, it's 0! ...
I am using nRF52840 DK as a SPI slave with an external MCU configured as SPI master. The SPI clock frequency is set to 1 MHz. I am using the following pins for SPI:
P0...
Hi All,
I have just got my nRF51 kit (S130) and started working on a beacon project which would transmit advertisements packets from peripherals over a RS485 to a server...
Hi,
im running my DK as a central of a BLE connection and i'd like to read the device_name of the peripheral board that im communication with. how do i do this? i cannot...
Testing on nrf52DK (QFAAB0), without softdevice, unfortunately still on SDK10 and
NRF52 sleeping on RTC. Programming pins disconnected.
Measured:
low frequency clock...
i am total beginner to the nrf51822. i am going through the nan-36_v1
app note is using s110 but i can't find that soft device in sdk ? is there any changes has to be done...
Hi,
I took the ble_hrs_c code and modified it such that it has the NUS service and can connect to 2 peripherals. The code works when I power cycle the central+2peripheral...
hi Engineers!
I am trying to use int. pullup of 160k but no effect. the voltage remains zero on pin.
config.resistor_p = NRF_SAADC_RESISTOR_PULLUP;
what problem?
...
Hi All,
sometimes i have a problems with bonding: the Nordic APP said "Couldn't pair with xxxxxx because of an incorrect PIN or passkey".
Why i have this errors? What...
Hi guys,
i'm trying experimental_ble_app_queued_writes out. I have some strange behavior.
The qwr service is
6e400001-b5a3-f393-e0a9-e50e24dcca9e but the characteristic...
