I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I am working on a project where my nrf51822 is on for long periods of time in lower power mode. Yesterday I made some updates to the code and the devices were working fine...
Hi Nordic team,
I print logs at each function in ble_bas.c. I used the App of nRF connect to test BAS. I can see on_connect, on_disconnect and on_write at enabling/disabling...
Hi,
The spec(nRF52832_PS_v1.3.pdf) said the peak current of TX/RX is 5.3/5.4 mA.
However, I use the PCA10040 board and the ble_app_template(SDK 12.2.0) sample code...
Hi,
I can see that Apple states that iPhone 7 supports LE Data Packet Length Extension forums.developer.apple.com/.../73168 . Anyone know if the packets per event and the...
Hi,
I have NRF51822 module with custom carrier board.
I trying the experimental ble app blinky (S130) with PCA10040 (master cenrtal board S132) works fine.
When trying...
Hello,
I test new SDK 13 and i have a problem. I don't success to debug bootloader. When i open .out file into debugger, sources are not complete (main is missing) so i...
Hello,
Is that possible to use a mbed application with SDK bootloader ? If yes, with signing too (if i sign application after generation) ?
How to set memory mapping...
I am trying to program an nRF52832 on an nRF52DK via the Debug in port (P18).
I am driving it with an STM32L073.
Should I put the nRF52832 into reset via the Debug in...
hai
in my application i am using nrf51822 . i have connected some sensors with the mcu. and i am collecting values from the sensors and this values are updated to the service...
In our code we use NV storage for system settings and calibration data.
I'm trying to understand when to open/close files and which structs to keep bwtween reads/writes...
Hello,
I'm using nrf51822/sd130/sdk12.1.0 and SOFTDEVICE_PRESENT defined.
But, I didn't enable softdevice.
I want to realize power save mode.
when I use __WFE...
hello there, i am using sdk11, i am using uart example. i am using nrf51 dk
SEGGER_RTT_WriteString is working. but
SEGGER_RTT_printf is not working. main.c
i have seen...
hello everybody,
i've downloaded the firmware files of nRF51822 beacon, but i couldn't find the source code. Does anybody know where i could find the source code of nrf51822...
Hello,
i try to use the nrfConnect (PC version) to update my devices via DFU. The DFU service is running on the device (update with Andoid nrfToolbox works without any...
