hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
I've installed and used the tools on other systems previously, no issues..
I have installed the tools on a new system, and can not get build configuration to run.
nRF...
Hello,
I'm using nRF5340 audio application with nRF Connect SDK v2.7.0 on nrf5340 Audio DK. I didn't change anything in the sample code.
I build by this cmd:python buildprog...
I used nRF52833 sdk17.1 to develop a device that is now going to use long distance. 17.1.0\examples\ble_peripheral\ble_app_uart\pca10100. Now what can I do to use his long...
Hi,
Using the Zephyr how can I set a TWI module clock frequency different from the standard speeds?
With nRF SDK I was able to do this by setting "frequency = 0x00290000UL...
Hello,
I am working in ncs1.5.0 on a nrf52840dk based custom board. I have found an issue where adding a certain number of characteristics in a single BLE service causing...
I have a general query regarding using ov7670 camera module with Zephyr SDK.
I have some of these camera modules available and I would like to try out how it works using...
This question is analog to but related to a Matter application. In this case, I'd like to separate the compilation of all Matter/CHIP related application parts from my own...
I am trying to use the ICM42688 sensor on I2C BUS with nrf5340 Application core. In the configuration, the HAS_I2C_RTIO config couldn't be enabled. Is this an MCU limitation...
I am trying to run the blinky Demo on the nRF52DK on VScode, the whole process is smoothly, but it can't work, the LED no any action. could you know anything I miss? many...
When I was making the upgrade package, I encountered a problem, and there was no problem in making only one upgrade package.
It is also possible to make protocol stacks...
Hi All,
Using VS code, nr52840dk,v2.6.0sdk，sid_end_device demo, No changes have been made
Firstly, add build config
Then click on Flash
Clicking VCOM0 has no logs...
Hello, I'm using the example "smp_client_ble," and I can't manage to remove the boot message.
Below is my .prj file:
My toolchain is: NRF Connect SDK V2.2.0
I am...
The chip I 'm using is the nRF52840, the sdk and toolchain versions are both 2.5.0, my code is here :
When I call spim3 peripheral with nrfx library, I add
CONFIG_NRFX_SPIM3...
Hello, hope to find you well. I'm a beginner involved in a project that's migrating from the old SDK to NRF Connect (VSCode). The project uses nrf_crypto.h and nrf_crypto_rng...
