hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi,
I am using TPS61021DSG in my design which is a data acquisition system using nRF52832 BLE module. I am using 1.4V Zinc-air battery to power up my circuit to generate...
Hi Nordic Team
I want to run the example project[802_15_4] on the soc chip 52820.So for the SDK17.0,it run and work well on soc chip 52840.
In order to run on the chip...
Hi,
I am using an Adafruit nrf52840 Feather board and have been having a problem with SPIM instance # 3.
I have the board connected to a display module and have been successful...
Hi,
This is not a ticket!
This is a project that I built. It uses the nRF52 to control a neopixel (ws2812b) via I2S over BLE using a custom mobile app built using the...
On SDK16.0.0 + Mesh SDK 4.1.0
I know that oversampling when using the SADDC in scan mode on multiple channels does not work because the buffer gets all out of order.
But...
Hi,
as describe in the title, we are getting a mesh assert when trying to remove all suscibtions from a model.
it is kind of hard to reproduce because this command is...
Hello,
I am testing direction finding over nRF5340 PDK.
I didn't have antenna array yet, but I think that's equivalent to signal received at 90 degree.
I have two questions...
Hi,
in SDK/components/libraries/timer/drv_rtc.h, there is some preprocessor define provided to select the RTC module (0, 1 or 2) used by app_timer2: APP_TIMER_V2_RTC0_ENABLED...
I want to trying to the HCI Command (DTM Mode) of CTE (Constant Tone Extension) feature for SIG RF Pre-TEST,
The nRF5 SDK v16.0.0 (latest version) is ready for CTE feature...
Hello,
So I am trying to build the ble_app_blinky_c example of SDK_14.2 to work for nRF52810 but encountered problems.
I used s132 v 5.1 for my softdevice by following...
Hi,
We have a project want to fixed "access address".
We want to fixed "access address" in every BLE connection (52840 as master)
Do you have some of API to assign ...
Hello, i made my own working NRF24L01+ using the reference design from the datasheet and it worked quite well. But i needed some more range so i wanted to add PA+LNA module...
[Google Translated]
Good day. I am new to application development. At the moment, I managed to implement a connection to nRF52832 using BLE via UART on an Android device...
Hi,
Greetings !
I want to take continuous 40 reading of adc by varying time interval between readings based on RPM value. I want timer interval resolution from 6 Sec...
