Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I want to wake up nRF9160 by SMS.
What I want to do:
The nRF9160 usually sleeps to reduce power consumption, and only when it receives SMS it wakes up and send some data...
HI i have issue while running the buttonless dfu with my application
I am using nRF52832 SDK15.3 SES windows 10.
I have to run my application with buttonless DFU so. i...
Question - How to enter in DFU mode using open USB bootloader example on pca10056 ?
i tried writing nRF52840DK with examples-DFU-open_botloader-pca10056_usb and usb_debug...
hello,
I recently updated SES and got a new version of nrfSDK.
Secure_boot sample does not contain Cmake. In other SDKs on github secure_boot does not exist.
is...
What is the best way to filter info center results to match my project? I'm using SDK 1.5.1 for S132 and I think that is softdevice 6.0.0.
It would seem like a simple top...
We are currently running on mfw_nrf9160_1.0.1 and NRF master as of today (Sept 13, commit 224bee9).
We are developing an MQTT application that uses TLS mode sockets.
We...
52832 & s112 & sd6.0 & sdk15.0
If you have multiple pairings on the same host will return error by “pm_device_identities_list_set”
err_code = BLE_ERROR_GAP_DEVICE_IDENTITIES_DUPLICATE...
Hello everyone,
I trying my nrf52832 getting ultra low power current conception mode using System OFF mode (0.3uA). I using SDK 15.2 ble_app_beacon example I change 32KHZ...
I started developing on the Adafruit nRF52 module. I wanted to make a custom PCB to demonstrate a prototype and fabricated a board with a MDBT42Q module from Raytac. I sent...
Hello, I have used the nrf52840 . I have created applicaction from existing examples of SDK which used bluetooth. And now want to add OTA via bluetooth. Is it possible use...
Hi,
I am developing an app based on PCA10059 dongle. my program work fine on this dongle, but i have a problem with it. after programming PCA10059 dongle with my firmware...
Like the title,
Is it possible to disconnect ble link or stop advertising at runtime, then change the service uuid and characteristics?
I wanna to do OTA service in application...
I am able to receive motion data [rawdata] from thingy52 on my RPi 4 using bluepy library in Python3.
I want to extract the raw values of Gyro/Accl/Mag from sensor.
The...
Hi,
I'm writing a program that swaps between LTE and GPS to send the device's location to AWS over MQTT. I am able to connect to LTE and AWS, then swap to GPS and get a...
Hello. I 've got such problem with flashing some of the ESB protocol examples of NRF5 SDK. I use Adafruit Feather NRF52832 board with ST-LINK V2 debugger. https://www.adafruit...
