hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi team,
There is connection between nrf52840 and ds18b20. I have made simple lib for ds18b20. When i get temerature without softdevice (s140) all works correct (use 9-bit...
Howdy,
I'm trying to access the SD card on my device via the usb MSC and am not sure the best way to proceed.
I have a custom board with an nrf52840, and it works great...
Hi,
I would like to make development on nRF52840-DK by using Segger Studio.
However, I could not find detailed document that specifies how I should start development...
Hello all
I was just following the thread launched by Alex concerning nrf 52 dongle driven from serial port, which is also very important to me, and now that thread is already...
Hi,
i would like to program my module nRF52840 via uart.
I generated private then public key using nrfutil.exe tool
i could programm softdevice and bootloader and...
I am trying to get the DCDC running on my custom NRF51822 board.
It is running but the results are a bit disappointing.
If I do a test and enable the TX with and without...
I've picked up a nRF52840 DK and dongle to do some testing with long-range beacons.
So far I think I have managed to configure my DK as a beacon in long-range mode (can...
Hi
I have a test mesh network, with several devices provisioned using nRF Mesh and.... a proxy node which has been provisioned using an alternative method but with the same...
Hi, I'm trying to make a SIG qualification Project. QDID97989 (nRF52 S132 V5.0.0) with replace PHY QDID97482(TaiyoYuden module). Launch Studio Project type is "qualification...
How to send and receive messages in ble mesh? The sending and receiving of sensor data I have done is not a switch value. I have tried many methods but failed.
I alredy run the assert tracking about 4 months ago on preliminary firmware.
Now I updated the modem firmware to v1.0.0 and compiled the last stable AT Client project from...
In the past we had a C based product that communicated from our Host processor over SPI to an nrf8001 peripheral using an Application Controller Interface (ACI) provided as...
Hi,
I am trying to set a fixed WiFi connection in the "/etc/wpa_supplicant/wpa_supplicant.conf " file, but it gets lost on every reboot. I assume it is because of the...
