I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello. I am working on a application in a NRF5238 with s132, where I send 20 byte packets using notifications from a peripheral to a central board. The central is a modified...
I updated to SDK v1.0.0 today and have not been able to build sample or application solutions since. I updated the SDK, modem FW, and SES.
For example, when I open and try...
Hi,
I'm sorry to borther you in your holiday.I got a issuse about 52810 (s112) with PA.I found my device would reset when I call ble_advertising_start() after calling pa_lna_init...
I'm trying to implement Serial Wire Debug to read some Data from Nordic from other Controller. Initially Need to read some registers in DP & AP Nordic. For that I need to...
Hi guys, i was using nrf51822 s130 sdk, and now i am using nrf52dk s132 sdk. When i am using nrf_adc.h, all bitfields macro's get errors. It's bitfield macros doesn't match...
I am trying to connect BLE app to BLE Device ( NRF 52840 ) and for security purpose, I adding passcode (password) / key in the device, once I am going for connecting it will...
I used serial program to talk between nrf52 and arduino where the rx tx pins were default 8 and 6.When i changed the pins to 25 and 26 it is not working i am not able to communicate...
Hello
I'm looking for someone to help write a custom bootloader which performs FOTA update by using an HTTP connection to collect firmware. NRF52 is connected to GSM module...
Hello, Dear Support!
I explore examples in SDK 15.3.0 : ble_app_hrs and ble_app_rscs. The peripheral device in ble_app_rscs is configured to wait active request from central...
Hi,
I use the calendar to display on the screen the actual date. It works but now I want to display it only when I press a button, but the button doesn't work. When I press...
Hello everyone,
I'm using the nrf52840 Dev Kit (PCA10056 1.1.0 2019.19 683465548)
SDK version: 15.3
OS: Fedora
I work on a custom board and try to put it in SYSTEM...
Hi,
We are using nRF51822 chip, and we are using TL3315 switches. I am very new to dealing with buttons. The current problem is that when I press the button, the MCU seems...
Hi,
I would like to flash a CC3100MOD wifi chip from TI with the Nordic 52832 chip as a host. Attached is my schematic. I am fairly new to the nordic family but I have...
Hi,
The problem statement mentioned below.
What we are trying to do is Read Light value from the MAX44009 sensor on the TWI interface.
Looking at the data sheet for...
Hi,
I am using Nordic nRF52840 SoC with nRF5_SDK_15.2.0_9412b96 (SDK) and S140 softdevice. I tried to set Tx power to +8dbm using
rc = sd_ble_gap_tx_power_set (BLE_GAP_TX_POWER_ROLE_ADV...
