I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Is there an event that I can hook into that fires when the soft device has finished it's connection and negotiation with the phone and is ready to send data to the phone ...
Is there any way to get some "modern" content assist features in µVision that work with the Nordic SDK? If they're there, I haven't had any luck finding them. After having...
I'm trying to decide whether to use FreeRTOS or simply build on the Scheduler. What are the risks and benefits of using freeRTOS or another RTOS on a wearable sensor device...
Is it possible to connected two separated antennas (single ended), one for RX and another for TX communications to the receiver and transmitter of the NRF51 or NRF52?
Thanks...
In other words, is it safe to assume that in various BLE events, conn_handle is either invalid (0xFFFF) or between 0 and (CENTRAL_LINK_COUNT + PERIPHERAL_LINK_COUNT - 1) ...
I'm digging my way through the examples, SDK code, etc, and I'm curious if it's possible to light an LED if the nRF52832 is reaching an error status. This is mainly so I can...
Hello,
I am seeing a strange problem with the nRF52 RADIO peripheral: sometimes a packet will be received that is corrupted, but the CRCSTATUS register indicates the CRC...
My company is developing an embedded product based on NRF52 and until now we are
using Master Control Panel (MCP) to test BLE communication. MCP is a great tool
but we need...
Hi,
when trying to connect to a 51822 target, using for example OOCD
I keep getting
....
Open On-Chip Debugger 0.10.0-rc1-dev-00001-gc404ff5-dirty (2016-12-29-19:45...
I use PPK wit ha stardard setup with all switches set to DK. Everything works fine, excepted that I have a little offset and the IDLE state is negative... which make the AVG...
I have designed a few PCBs using the NRF52 chip with a standard QFN48 pattern. On the first design, we had 8 PCB's made of which, only 2 worked correctly. The others all exhibited...
Hello,
I received BLE_ERROR_GATTS_SYS_ATTR_MISSING event during connection procedure. Tried to look inside and found
/**@brief Event structure for @ref BLE_GATTS_EVT_SYS_ATTR_MISSING...
In code:
case PM_EVT_BONDED_PEER_CONNECTED:
NRF_LOG_DEBUG("Connected to previously bonded device\r\n");
err_code = pm_peer_rank_highest(p_evt->peer_id);
i get...
