hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Has anyone ever used nf51 bluetooth with the app inventor?
I have values coming out of the microcontroller terminal. I want to send them to a mobile application using...
I've got a few questions regarding memory of nRF51DK.
I would like to know what is the total memory size of the nRF51DK board?
What is the memory size allocated...
It looks to me like ANT_STACK_CONFIG is redundant in SDK 14.0.
nrf_sdh_ant_enable does all the same setup plus, it looks after all the new softdevice handler stuff.
...
Hi,
When I use nrfutil to generate a zip package, there would be three document in the package. Is there anyone know what does .dat and .json document use for? Could I...
Hi there,
I am begineer for nrf51822 and I want to interface MPU6050 WITH nrf51822 so can somebody provide me the tutorial with full detail.i want to read just raw values...
Have been following the nordic tutorial to update characteristic value using hvx_params. Currently the structure for hvx_params is as follows:
/**@brief GATT HVx parameters...
Hello every!
I am working with ATT_MTU_Thoughtput example (S132). My purpose is send data from "sever" to "client" and wait until "client" response to confirm . I was send...
I’m debugging the ble_app_blinky demo on a nRF52840-Preview-DK board (BOARD_PCA10056, S140). The device name in the debug configuration is nrf52832_xxaa.
Each time a breakpoint...
Hi all,
i use a nrf52 and in product specification i find the table about the low power mode and their consumption . Capter 17.1.
ION_RAMOFF_EVENT System ON, No RAM...
Hi all,
I have been playing with my PCA10040 and I came across the problem. I thought that it was a softdevice problem, so I went to bootloader mode (by connecting with...
Hi,
would it be possible to have multiple GAP Addresses for one nRF device? I was able to have this with the S130/S132 using verison 2.0.1 by using gap_address_set and...
Hi,
I have nRF52840 dev board which was detected and LEDs were coming on.
I tried programming the prebuilt throughput hex file in nRFgo Studio.
C:\Projects\NORDIC\nRF5_SDK_14...
Hello dear sir/madam, i have just started with BLE using nRF52832 DK .but i am not able to understand the examples.and don't know how to make any change.what is the basic...
My nRF5x DK kit has suddenly stopped working and I experience one or more of the following symptoms:
My kit doesn't show up in my computer.
LED 5 on my kit doesn...
Hi,
I have a ble scanner working well and i am trying to trigger start a compare timer within a timeslot.
starting the timer in the timeslot with the below code makes...
