Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Hello.
I need to use LESC numeric comparison pairing.
It seems that the PIN is automatically and ramdomly generated after the connection occurs.
I would need to manage...
I am running a nrf52 with IOT sdk's Cloud CoAP example. I am wondering about the parameters that I would need to integrate this into a product. These include the stack size...
Hello,
I am using 52832 to test ble data throughput. When two devices are close to each other, the throughput can reach 80kB/s, but if the distance is about 4 meters, the...
The nRF51422 product specification says that you have to use a +-40 ppm crystal for BLE applications.
On DigiKey, there are 2 columns for 2520 crystals: frequency stability...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
Hello, I downloaded the ble_mesh_v0.9.1-Alpha source code from nordic website, and tried to port it to my pca10056 devboard.
When doing so, I noticed that some function...
Hi All,
I would like to use FreeRTOS in my project. I try to play with the examples/ble_peripheral/ble_app_hrs_freertos project.
I have enabled logging with RTT. The...
Hi, when reading BLE Mesh specs, this paragraph caught my attention:
Messages may support a delay parameter that indicates a delay between receiving a message and
starting...
nRF5 SDK v13.0.0
Release Date: Week 11, 2017
Highlights:
Implemented a new license scheme for the SDK distribution. See the
documentation folder for details....
Hi,
I am using "nrf5 sdk v11.0" ble_peripheral "ble_ancs_c" example for nrf52_DK(PCA10040) .
When i connect to the my ios device then accepted pairing request then i am...
is it possible configure the QDEC to single phase, i am using one omnipolar hall effect sensor i am wondering if i can configure only phase A ande use it, is it possible ...
Hi, I wonder why my pwm uses so much power in WFI mode. It uses around 470uA and when I do not use pwm that current is around 1.8uA. I tried to disable pwm but without success...
if i am not wrong the connections i found is as i shown in the image..
the module doesn't show up in my ide tool (keil ) although my kit works fine but i need it for standalone...
Dear Nordic Team,
I am work DFU with ble_app_uart example , as per the info center document : infocenter.nordicsemi.com/index.jsp and also followed by the example for ble_app_hrs...
when use the sd_ble_gatts_hvx() send data and printf() the value below
p_ble_evt->evt.gatts_evt.params.hvc.handle
p_ble_evt->evt.gatts_evt.params.sys_attr_missing.hint...
