hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi,
So I'm fairly new to programming the nrf51822 and using the Nordic platform.
I'm currently using the nrf51822 Waveshare DK. I have setup JLink5.1.2, nrf5_MDK_8_5_0...
Hello,
I am using SD 130 on nRF5 with SDK V12.1.0.
I want to write to a characteristic using the android debug app (nrf connect).
This is my code for the characteristic...
Greetings,
As mentioned in this blog post, GCC compiler -flto flag isn't mysteriously present since SDK 9.
devzone.nordicsemi.com/.../
Any specific reason for this...
Hello,
I use a SparkFun programmer to flash a nRF52832, once I flash my board (with the program below), I type in my terminal : "JLinkExe -device nRF52 -speed 4000 -if SWD...
I have many peripherals, dealing with each of them individually will be very ineffective. The peripheral has no buttons, but it has a display.
Questions :
For security...
Hi,
In my application of interfacing SD card with nrf52, I am using SAADC to sample the input signal at 1000 samples per seconds. These samples I am combining in 84 packets...
I have set up ble_app_uart along with gpiote and spi. When I first trigger the GPIOTE event the MCU is supposed to go to sleep after, but it seems to keep running in the main...
Hi Everybody!
I'm trying to integrate a buttonless dfu into my application but I'm not able to get even the provided example in SDK 12.2.0 "experimental_ble_app_buttonless_dfu...
Hi,
When calling app_sched_event_put inside the same hanler i am exit to main for(;;)
The main loop
for (;;)
{
nrf_drv_wdt_channel_feed(m_channel_id);
app_sched_execute...
Hi,
What is the valid configuration for SAADC with oversampling for nrf52 sdl12.2
I try
SAADC config
SAADC_CONFIG_OVERSAMPLE 4
nrf_saadc_channel_config_t channel_config...
Dear Nordic Team,
Thanks for supporting.
I have a nRF51822 Board (PCA10028) and Also i have arduino code for reabear from ( github.com/.../nRF51822-Arduino )this link...
Hi, all great guys,
We are using NRF51822 as the MCU,and met a very strange problem about the current consumption in our application. Normally,the lowest standby current...
Hi.
I'm new to Nordic BLE devices. Using the nrf51-DK.
I have a peripheral device (non-Nordic) which I want to connect to from a Nordic central (S130) using the public address...
Hello, I want to change mode from radio test example from button input.
How can I use the gpiote for mode change from button input.
I only want to use modulated and unmodulated...
