I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
Now I'm using nrf52840 as a master and some other ble chips as multi peripherals.
As I know, in ble link layer data header, there is a tag: MD(More Data) , by which, every...
I installed nRF Connect Desktop. Opened Tool Manager. After sucessful installation, I tried to create ny first project by opening SES through nRF. The selections used are...
Hi,
I am using the ppk II, and I have had a number of occasions where the current displayed on the PC suddenly disappears (see attached). The voltage to the DUT seems...
Hi,
I'm testing the nRF9160 GPS performance with a GPS simulator. I set the output power to -130 dBm and test the nRF9160DK conductively. I made some small modifications...
Is there any guide or sample how to run unity tests on a target device instead of the native_posix device?
In general unity however cmock support on-device testing like...
Hello,
My config: - nRF SDK v17.1.0 - nRF SoftDevice S140 7.2.0 - FreeRTOS Kernel v10.0.0 (Amazon.com)
My project used BLE connection with custom service (based on NUS...
I want to use dynamic memory allocation. After searching these forums, I see the following options:
malloc
k_malloc
nrf_malloc
balloc
I haven't had success with...
Hello everyone I hope you all had a good start to the week. I am stuck with an issue I don't quite get. I wrote code with BLE, FreeRTOS, and GPIOTE as a "proof of concept...
Hi,
I'm evaluating the NCS peripheral_uart example for our needs.
I have an issue with deploying this example to an PCA10040 board. While running the example built for...
Hi All!
I have a problem which i can't really understood. I'm using nRF5340-DK evaluation board, and currently i'm trying to get one of timer (TIMER1 in this example)...
Hello,
I have a Nordic connected to a STM32. The DFU procedure on the Nordic works fine and I am able to upload and run a new firmware in buttonless mode. The Nordic also...
nPM1100 use JEITA profile that has charging range 0-60gc. Most batteries has charging range 0-45gc. Is it possible to limit charging to 0-45gc with this chip, or is JEITA...
Hi,
I am developing a product using the SoftDevcie s140 and SDK 17.0.2.
I have the problem, that the standard FreeRTOS port defines configTICK_SOURCE to FREERTOS_USE_RTC...
