Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Hi Sir,
We have designed custom nRF52832 board in PCB design layout have 4 Pin connector VDD, SWCLK, SWD, GND. I know how to use nRF52832 DK for programming. But for other...
Hi,
I am using SDK12.3 and stack s132 with NRF52832. We have to store 3 variables in flash memory and keep updating it once BLE connection is formed with the phone. We were...
Hi,
I use nrf5_SDK_for_Mesh_v1.0.1_src SDK to debug mesh in SEGGER Embedded Studio for ARM 3.34. The projects are all based on NRF52832, but I want to debug it on 51822QFAC...
Hi,
I have been using the following parameters to flash program the example ble_app_uart_c_s130_pca10028 (SDK 9) but the problem is the it uses the S130 v1.0.0 softdevice...
Hi,
I have a newbie question. Is it possible to implement a POTS voice quality like an intercom system using Thread (assuming all the end points are using nrf52840 SOC...
We are trying to minimize the UART current in our product, so we tried some experiments on the PCA10040 board.
We noticed a significant current difference between SDK11...
SDK14.2.0 sd132v5.0.0 nRF52832
I've looked for a solution to my issue on the discussion forum, but can't find an answer. I am working with the buttonless DFU peripheral...
I have two nRF52832 devices. One of them I have been using for a while and the other is brand new. My BLE application will flash and run just fine on the old device but not...
Hello,
I read in your datasheet the follwoing:
"32.768 kHz synthesized from HFCLK (LFSYNT)
LFCLK can also be synthesized from the HFCLK clock source. The accuracy...
Hello,
in the Online Power Profiler , the current consumption increases, when the voltage is reduced. What is the reason for this?
Isn't there any documentation on the...
Hi
I need to capture a serial bit stream which consists of a sequence of 16 bit words, package them up and transmit over a bluetooth interface - it's a datalogger application...
Hi!
I have some troubles with making embedded serial port working on NRF52-DK. Basically I can receive data sent by nrf chip but I cant write. When I write something using...
More of a suggestion than a question:
Using the info available on the infoCenter, especially here and here , I'm trying to implement a way to dynamically select the DFU...
I use Adafruit Bluefruit library and developing code to run on Fanstell BT832.
Up to know i have been able to compile several examples and run it on the NRF52 DK board....
