Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
Hi. I'm currently using nrf8001 and i need to send data consecutively and as fast as possible.
Connection interval used: 20ms
Data payload: 20bytes
Service pipe used...
Hello.
I'd like to set up my Secure DFU bootloader so that bonding is required to activate the bootloader from a peer device (phone). But at the same time I'd like to make...
I am using the secure DFU bootloader without bonding. Sometimes it DFUs successfully. Sometimes it produces this. I notice there is an error 0x200204, which I believe implies...
Hi I`m new to nrf so pls forgive me if this been asked before. 1. nrf52840 dk. Flash twi_scanner_pca10056 via nrfgo, verify ok.
2. At the moment I have no I2C devices connected...
Hello! I had asked a question about zigbee to parsing xiaomi data here . But there is no answer for my last ? .
tomchy adviced me this solution:
...
- register an endpoint...
Dear Sir, we are developing an application on the nRF52840 kit with SDK 15.0.0. We are using Keil as compiler. In our application we need to receive data from two uart together...
I have a test program that does a simple call to fds_record_write() to write a 4 byte value to an FDS file. This is using the NVMC backend. I happened to stop the debugger...
Hi!
Can anyone from Nordic pinpoint where exactly in buttonless project or bootloader project NRF_DFU_SVCI_ENABLED definition is used? I mean 15.0 and 15.2 SDK.
I have...
Hi, i need an advice.
It said in nRF51822 datasheet at p.11.1 (PCB guidelines) that "The supply voltage for the chip should be filtered and routed separately from the supply...
I have upgraded to the more recent J-link RTT Viewer.
If I start Debug Session in uVision and run RTT Viewer, I can connect just fine and have checked the Existing Session...
In the nrf5 sdk (version 11.0.0) there are three different modules which, as near as I can tell, do the same thing. These are:
pstorage
fstorage
ble_flash
...
hi........... nrf523
how to read the data from peripheral and send the data over ble using ble uart
i have merged the two programs ble_uart and twi sensor ,what changes...
Hi,
I'm trying to flash the mesh lightswitch example on Bluemod S42 custom board, please help me with what are the steps to be taken to flash on custom board.
Hi,
As the tile says, I'm using BPA600 capturing mesh logs and analyze.
Since BPA600 needs to configure "MeshOptions.ini" to be able to decode the logs, it needs "IVindex...
