Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
I figured that I could put
#define TX_POWER_PHIL +8 /** -40,-20,-16,-12,-8,-4,0,+2,+3,+4,+5,+6,+7,+8 phil **/
and then make two changes to
static void advertising_init...
Is any GPIO, as output, logic level on nRF52832 maintained when the device is in OFF mode? Same question when the system is in ON/Low power mode Thank you
Hi guys!
I am making an application that uses the PCA10056 for 2.4Ghz RF communication using Enhenced shock burst(esb).
Also, when upgrading the application, i try to...
Hi all. I fell into despair in an attempt to find a solution. If I do not use sprintf then everything works fine.
Before calling some_f, mqtt_put works without any grudges...
Function softdevice_enable() doesn't return any adjusted warnings in case of changing central/peripheral connections, e.g. my ble_stack_init() function:
static void ble_stack_init...
Hello, nordic.
I studing nfc example for oob pairing.
So, I have to intergrate to uart example and hrs nfc example.
I had intergrated uart function in hrs_nfc example...
I am trying to decide whether to use free-rtos or bare-metal.
In the documentation for the nRF SDK v15.0.0 i see that free-rtos is not supported for the nRF52840.
However...
SDK14.2
A little background on this question.
I am creating a library where I need to add items to a queue and then process those items from the queue. I would like to...
PLEASE revise the page Getting-started-with-the-rRF52-Development-Kit to include
"confirm that the nRF52 DK has appeared as a removable drive named "JLINK"...
If drive...
Hi,
Iam using serialization application code from sdk14 nRF5_SDK_14.2.0_17b948a/examples/ble_central/ble_app_blinky_c and
connectivity code from sdk14 nRF5_SDK_14.2.0_17b948a...
Hello everyone,
Similar question like mine was asked, but I didn't quiet get the answer i was looking for. I will try to keep it simple, when I open altium files of thingy52...
Hello,
I am evaluating the module MBN52832 from Murata (Using the development kit). I have installed nRF Connect v2.3 and I have installed and launched Bluetooth Low Energy...
Hi,
In this topic , i was asking about how to increase range in mesh networks. I did some outdoors tests (clear field), changing power (-40, +4, +8 dBm) and mode (1MB and...
I am using nrf52832 to develop based on SDK14.2. I have defined a custom service . There are 7 characteristic in this service. The attribute of each characteristic is set...
When broadcasting mesh messages I use the access_reliable_t struct to set data.
I need clarification on what the contents indicate. The documentation is sparse and doesn...
