We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I would like to modificate the LED Button application example. The LED characteristic should stay as it is, only the Button characteristic should be changed. I want to use...
Hi,
I have used several Bluetooth Low Energy solutions and I looked into several examples and something is missing. What I miss is to prevent pairing. It is something quite...
In SDK source code of S110 SOftdevice, I'v found two events for which module is registered and waiting using "softdevice_sys_evt_handler_set" & "softdevice_ble_evt_handler_set...
Hi,
I'm working on getting our product through BLE certification and they are asking a few quesion's that I'm not sure about.
1: Pairing. Is it using a fixed PIN or...
Hi,
Routine running normally in low power mode with power_manage() .
but after sd_flash_write/erase current consumption goes high(almost 20mA).
If anything is missing...
Hello,
i want to update the softdevice S310 V1.0.0 to version V2.0.1. My applicatio based on SDK 6.1. With S310 V1.0.0 all works fine. But i can't update to S310 V2.0.1...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hello, I have a problem with GPIO Input control
My sensor work on special clock generated by MCU
I've controlled this sensor by Arduino like this
//SCK digital pin...
We are using the NR51422 to develop a BLE application. We reused the project “ble_app_hrm” from the SDK v6 and ran it using the NRF6310 board, everything is ok.
We just...
Hello Everyone, right now i use nrf51-dev kit and i want blinky code for that, in Keil i compile code and load in kit and it work fine but now i want to make code in eclipse...
I'm trying to debug the blinky example with SDK 7.1 using Eclipse Luna. Going through several threads here I could figure out configurations needed and build the app. I can...
Hi,
I have been trying to study how to implement support for over-the-air (OTA) updates in my current S110-based project. But I'm already stuck in the very beginning. How...
I am using softdevice and RTX at the same time.
RTX is using RTC1, softdevice is using RTC0, so no problem there.
But sd_softdevice_enable require a clock source as one...
Hi,
I have problem with nRF51 antenna orientation. I used nRF51 developement kit (mKIT) board and I had problem with communication if I just change a little inorientation...
Can I change the shared channel address (first one or first two bytes in the message) when the channel is open?
The manual says after opening the channel, send a broadcast...
