nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
I am using 9160 as slave which communicates with nrf5340(master) over UART. with flow control disabled everything works but as soon as I enable the hardware flow control then...
Hello,
I have a few questions regarding the nPM1300 current measurements:
As far as I understand, there are two ways to trigger a current measurement:
By writing...
I am using VS Code IDE and have installed nrf Connect Extension and done with the installation part and blinky and few other samples. So, basically I just copied an available...
I have figured out a way to realize IR communication,it is same with the way to drive WS2812 with SPI.
[ I can use PWM peripheral and should use it,for I need to change...
Just to confirm the head question.
I have found the same question : NRF52 help configuring TIMER + DMA + PWM - Nordic Q&A - Nordic DevZone - Nordic DevZone
There is no...
Hello,
1. Do you have any hardware to implement Wireless HID USB without Bluetooth like Logitech with USB dongle?
2. Do you have an example of IR TV remote for any hardware...
Hello,
NCS 2.9.0 nRF54L15 DK 0.9.1
I am trying to follow the instructions in the manual in the User Guide of the nRF54L15 DK to use P1.00 and P1.01 as normal GPIOs. (side...
Hello,
I have been following the steps in Exercise 1 of Lesson 1 of the Cellular IoT Fundamentals course. I have a Thingy:91. I have followed the steps so far
- flashed...
Hi
Long time no see
I recently got my sweaty hands on a sparkly new 54L15DK, and I thought I would try it out. The AI guided me to the coremark sample and the multicore...
I recently tired the Onomondo static and external softSim demo on the nRF9151 DK. For both of the demos they take around 4 minutes until the DK gets a cellular connection...
What is the connector cable that fits with nRF5340 DK J1, I am using the other end to connect to the ANT-B10 J2 (antenna board). I will like to know which connector cable...
I am currently trying to add MCU boot to my application using sysbuild. I have done the following :
Created sysbuild.conf in application root
Created sysbuild folder...
I cannot get the nrf5340 audio dk kit to work from USB input properly. After a reset, it only works for a fraction of a second and audio stops. Has anyone run into a similar...
hi,
i am trying to connect peripherials ( blood pressure, pulseox meter) with nrf5340 dk ( development kit from nordic PCA10095) using uuid and mac, initially using uuid...
