Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
hi ,
thank for your browse,when i develop my keyborad,there is a problem in the use of usb.
this is my board hw:
and use pca10056 kd,and program the hex of road...
Hello, everyone!
I have arduino nano 33 ble board. I understand that this board contains nrf52840 and can be used in nrf sdk. I will connect the debugger pin and J-link...
Hello!
I am using an saadc examole to get sensor value using AIN3 and sending it on ble but now i want to make it interrupt base example can someone help me out how to do...
I am researching a way to send audio from a Microphone on an APP in iOS or Android and came across the Thingy:52. Is it possible to get some guidance on the App side to transmit...
I would like to use an analog microphone to generate a voice signal, measure it by an ADC, and then transmit the sound to the host. This is the cheapest solution, but I'm...
Hello,
I'm trying DFU from here . It works successfully with nRF52833 DK Board before Appendix 1.
The question is how to combine all which it is bootloader + sd +...
Hello all, I have question about ppi.
Like code shown above, I'm using ppi.
Here, MUX_INPUT_2 and MUX_INPUT_3 are name of pin.
I'm changing their state: from low to...
Hi,
We would like to know the default state of the NRF52840’s GPIO pins - is it high, low or open? The reason for this question – we need to know these pins’ behavior/state...
Hello Guys, I want to build some project with Nordic products but ı don't have any sample code , if you have sample code for Keil let me improve myself.Actually codes can...
Hi,
As has been explained numerous times in posts on this forum and many others, mapping RSSI to a distance measurement is notoriously difficult and inaccurate. I was...
Hi
Can anyone verify that it is possible to use the nRF5340 PDK to program custom nRF53 board?
The documentation says: The nRF5340 PDK supports programming and debugging...
Hello,
we are using NRF9160 +Nrf52832 in a project. NRf52832 has to be used as HCI interface..after searching for this, i came to know that zephyr based HCI uart sample...
Hi,
I am working on Eddystone project, after I successfully tested the Buttonless DFU example, I added DFU service to Eddystone example ( nRF5_SDK_17.0.0_9d13099\examples...
I am using this MBN52832DK and find out this nRF5_SDK_17.0.0_9d13099.
Trying to import into Segger Embedded Studio but rebuild come out error.
using the nrf52832_xxaa...
Hi all,
I would like to have a semi-duplex communication link over one pin (+GND). The nRF will act as a pure slave device which responds to, and acknowledges, commands...