VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Dear Team,
I have a problem with one sensor on some boards, the behavior is not clearly reproducible. On some boards, the "device_get_binding("CCS811")" just delivers exit...
Section 18.6.2 of the nRF52832 datasheet (Power-On reset) specifies the following:
A step increase in supply voltage of 300 mV or more, with rise time of 300 ms...
Hello,
I have tried the GPS sample and it worked fine. Now I want to understand the code more in detail und maybe modify the GPS settings.
But I can’t find any documentation...
Hello NRF Team,
Is it possible to change the I2S buffer size on the fly while a i2s transfer is running ? (I Am using nRf52840 with SDK15.2)
I found in the documentation...
Hi, I am evaluating the nrf52832 and the Softdevice for potential use in a new product. The product has neither display nor keyboard. It therefore makes sense to use Just...
Hello,
I am quite new to developing with the nRF52840-DK. Up to this point, I have been flashing the applications (mostly the examples) over USB with the built-in J-Link...
We need to connect 2 peripherals with single central device.I have taken ble_app_multilink_central from SDK 15.3 and integrated the ble_app_uart_c in this. I am using the...
Hello,
I want to establish an UART communication with rn2483 module with nrf52-DK, SDK 15.2.0
On nrf52-DK, pins 6 and 8 are reserved for serial port, which are connected...
Hello
I used to do TWI communication until now, but it was decided to do sensor reading with SPI communication by changing the sensor.
So that's a question,
What is...
Hello,
I am wondering that when BLE5.1 SDK will be available ?
Is there any possible ways to test your BLE direction finding solution ?
As far as I know, development...
I want to set a keep alive value of MQTT while eDRX is enabled, but it doesn't work well. Any advice?
Environment - hardware: nRF9160 DK 0.8.2 - firmware: 0.7.0-29.alpha...
Hi,
I am using nRF52832 SOC along with SDK v15.2.0 with custom hardware, currently I have requirement to use DFU protocol in BLE application to get a FW of another sub system...
Hello, I hope your day is full of the scent of flowers.
I am in the process of the Ble_Cnetral and PrePhereal project.
I have added and built the Uart.
Why is...
Hi frnds,
I am using the ble_central and ble_peripheral code (nrf52840).
i am sending 400 bytes of data to central from peripheral continuously, sometimes the boards get...
