Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I have an application that performs a task and saves the result to EEPROM that uses an ATMEL ATMEGA168pa processor.
I want to convert it to the nRF52840 which does not have...
Hello! We have been trying over the past week to figure out how to best back up a provisioner/client so that if it goes down we can rebuild the network without re-provisioning...
Dear Team Nordic,
dear Community,
I'm working on a project with nRF24L01+ transceivers where I have two types of devices: a so called Basestation which acts as a Primary...
Hi all,
I am using nRF SDK for Mesh v1.0.1 and I want to implement following as in picture:
I am publishing to group address (group address because in the future I...
Hi, I test the SDK example "temperature", it works OK. I copy the code to my project, there is no compile error, but when the code running on the DK pca10040, the code is...
Hello there,
I'd like to bond between two nrf5 modules and have a real time communication between them.
Now my question is what is the role each would have to play...
The nRF5 SDK is event-driven. So does it mean that the event handler in my application will be directly called in the interrupt service routine? If I write a long event handler...
Hi all,
I'm experiencing a performance drop with BLE proxy enabled in Mesh SDK 2.0.1 compared to Mesh SDK 2.0.1 / Mesh SDK 1.0.1 without proxies (higher packet loss, range...
Hi,
I have project for NRF51822 in IAR(EWARM). Short about project: it based on example BLE to UART communication; it uses SPI, I2C, analog inputs readings, some digital...
I used nRF5_SDK_14.1.0_1dda907.
I opened the bpwr channel then received ant+ packet.
The device received ant+ packet successful.
How do i know that how long time the...
hi all ,
how to build multi provisioneers with mesh network ?
i read some information and run the nordic mesh sdk 2.01 (ligh_ swith sample )
i have some issue with...
1. I am issuing a gatt characteristic (CHR1) write without the response requested from Central (BLUEPY/BLUEZ, Ubuntu 18)
2. Central than reads CHR2.
Is it possible...
Hello,
If I understand well, when the part of the flash reserved for the PM is full, new bonds cannot be saved until the application deletes older bonding data.
I would...
Hi,
I've heard some stories that that using analog capable pins for digital IO (UART in our case) results in significantly higher power consumption than using a pin that...
