VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
I'm using JLinkExe ( J link commander ) for Linux to flash the application firmware on NRF51822_QF_AA target. The following have worked so far, but I'd like to confirm and...
Hi,
I am upgrading to SDK 11.0.0 and S130 v2.0.0 from SDK 9.0.0 and S130 1.0.0 and I am stuck with an error when I call sd_ble_gap_adv_start. Here's the code that now fails...
I have the following two lines with pin 21 not connected to anything:
nrf_gpio_cfg_input(21, NRF_GPIO_PIN_PULLUP);
uint32_t value = nrf_gpio_pin_read(21);
I would...
Hello!
I'm trying to flash my SeeedStudio Tiny BLE board (nRF51822 QFAA) with SoftDevice S110 using Keil but it doesn't look like it's going to let me. I'm just getting...
Hi,
i am having some trouble getting my nRF52 DK (S132) to read a value provided by the nRF51 dongle(S130).
First of all, i am very new to this whole Bluetooth thing so...
Hello!
I'm trying to read 16 bit ADC Value on nRF Master app instead of only 8 bit, and I know that there is the example code on github which is only send me the 8 bit...
We have a new daughter board connected via I2C to an Atmel controller. What we need to do is load the right softstack onto the NRF and then send the needed commands to tell...
Hi Guys,
We have schematic of future NRF 51822 project, who can help us with PCB design? Or who can suggest me where i can do it?
PCB.DXF
schematic.pdf
Hello All,
I am trying to build a BLE peripheral project with RTX OS which is using S110 Soft Device and bootloader is also there in Flash memory region. So when I am trying...
I am just beginning to develop with BLE.I came across the nRFgo Studio through Nordic and BDS through the bluetooth SIG.
1]What are similarities/differences between the...
Hi.
I want to active HW timer with SoftDevice 7.1.0 .
Timer operation is good but I can not stop the timer.
The power consumption is 200~300uA after timer expired ( or...
Hi,
We would like to use NRF52832 chipset for our project, and we need to configure 11 pins as GPIO interupt , Is this possible ? How many pins we can have as interrupt...
