Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
I am using nRF52840 to interface my MPU6050 sensor via I2C , I build and flashed the program and there were no problem. But I can't see any clock signal on the default I2C...
I'm trying to build the zephyr/samples/net/sockets/http_client. I selected thingy91_nrf9160_ns for the board config and it builds and works fine. However when I enable
...
In my project, need an external sram with SPI interface to increase the sram volume.
I'm not sure if I can do it，please give an exsample in C language and some tips.
An...
Some of the products we produce do not work after about 10 days. Our firmware starts the watchdog module as soon as it starts, and sets the timeout period to 30s. And read...
I would like to implement ANALOG Modulation schemas on nrf52 serias family (e.g. AM, FM, SSB)
Do I have a direct access to IQ samples OR basic properties of the radio carrier...
I am using is25lp03d flash with "nordic,qspi-nor" driver.
The issue is that nrf_qspi_nor.c driver uses `nrfx_qspi_mem_busy_check()` before entering suspend mode. This function...
The %XCONNSTAT read command returns the total amount of data received/transmitted "in kilobytes". By kilobytes, does the documentation mean 1000 bytes or 1024 bytes?
Hi
I would like to have a project using 52840 witth softdevice 17, and I need to use internal flash to make a USB mass storage device
I reference to ....\examples...
Hi,
I need to create partition of size 4kb but using psa_ps_set() I could not able create partition of size more than 1Kb, If I try to create 4 kb Partition it's throwing...
Hello,
Creating a simple project in nrf connect 2.6.1 I start with looking at power consumption.
I need upgrade over USB, so I have added this to .prj:
In the...
software: ncs 2.5.0, zephyr\samples\drivers\counter\alarm
hardware: nRF52840dk
Step1: main.c is not be r evised!!!
Step2: prj.conf like this:
Step3: overlay file...
Hi Nordic Team,
I am currently working on a project that involves two devices, both using the nRF52840 microcontroller.
Current Setup:
Device A : I have successfully...
hello Nordic
we are working with ncs v2.5.0 trying to migrate to 2.7.0
1. so that there is several rcs, should i take v2.7.0-rc3 or v2.7.0 ?
2. while choosing v2.7.0...
Hi all,
I wonder if nrf9160 has a built-in temperature sensor interfaced with the ADC, that could help to diagnose the internal chip temperature?
Thanks.
