When both ethernet and WiFi are supported on one MCU (with both sharing the same L2 implementation, only one network device being active at a time), does it matter if both...
we have a custom board with nRF9160, when using GNSS we configured it to periodic mode with 120 second interval, most time it works fine but every once in a while (like every...
Since I need zephyr version 4.0 or newer, I tried updating my project to the nRF Connect SDK v3.0.0 as well as the toolchain. I know that they are not fully released yet....
Hello,
I am a beginner when working with nRF. I am trying to run the l4_e3 solution code, but it doesn't seem to work. I can connect via BLE, but nothing is being shown...
I am currently in the process of filling out the 18031 RED Cybersecurity certification documentation. I am currently analyzing the security vulnerabilities list of NCS v1...
Hi,
We’ve designed a project using the nRF5340 + nRF7002 combination, with Wi-Fi connectivity enabled.
As part of our preparations for FCC certification, we’re currently...
working with a nrf52833, soft device 140.
I am trying to setup a whitelist with a known addresses before I start scanning. I am calling the following code before my main...
Dear Team,
I am migrating the ANCS client application from SDK-12.3 to SDK-15.3 version.
Please find my below observations in SDK-15.3.
Erase the flash completely and...
Hi All,
I'm developing my product based on nrf51822.
I was using keil IDE for that.but i wanted to develop it in Segger instead keil ide.
is segger is supporting for...
Hello, I am working on an IoT project. For this project , I need to send some data using BLE. I developed a firmware for this application based on the sample ncs/zephyr/samples...
HI ,
In our project we are using multiple gpiote and app timer interrupt.
SDK we are using is 15.3
DOUBTS
If both gpiote and app timer interrupt trigger simultaneously...
Hi,
I'm using nRF mesh library v1.2.1 and integrating into my mobile application which I am developing, I implemented provision functionality without errors but sometimes...
I am bringing up a custom board based on the PCA10040.
As the first step, I simply copied (no changes) the file pca10040.h and named it as "my_custom.h". I then defined...
We have an nRF52 DK system running ble_app_uart_c example code and communicating with a peripheral device. We setup a second development system using another nRF52 DK system...
I have the nRF52840-DK with the adafruit PN532 RFID/NFC shield installed on top of it.
I run the TWI Scanner and receive a report that a device was found at address 0x24...
I am having a strange issue with my custom radio protocol. I have ported the code to the 52840 and SDK15 from the nrf51822 where it is running with no issues.
The issue...
Hello,
I have PCA10040 development board with nRF52832, Softdevice S132 v6.1.0 & SDK 15.1.0). I wanted to use the extended advertisement feature to advertise more than 255...
Hi,
After developing two application, one for emitting extended advertising and other one for scanning this kind of advertising on nRF52840 DK (Github repository here: MOTAM...
Hi,
I would like to ask two questions.
1)
I understand that the nrf52832 does not support the feature "Transmitter has a Stable Modulation Index".
But the component...
Hello, I am trying to build the asset tracker reference app for my newly acquired Thingy:91.
I went through the instructions to get the toolchain and SEGGER IDE up and...
Hello,
We are currently using a Raytac SoM that has nRF51822 SoC with Adafruit UART firmware. We are running into two different scenarios BLE connectivity issues where the...
