Hi everybody I'm using nRF Connect SDK 2.6.1. I have my own board based on nRF52840 SoC. I made an overlay file of nRF52840DK and changed its UART TX/RX settings according...
Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
In the past few months I got aware, that some, in my opinion simple questions, get marked with
"This comment is under review"
and then nothing happens. For weeks, even...
running Windows 10 Pro 22H2 and using j-link v9
i tried to read firmware from nrf51822-QFAB by using " nrfjprog --readcode dump_nRF51822.hex", but it gave me an error...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hi Nordic Engineer,
We want to interface NRF52840 with MTK7628 over UART. Is there a client library for nrf52840 which we can integrate with our application which runs on...
Hi!
I am trying to get scan_req_notification to fire notifications when central devices issue scan reqs but without success until now. Here is my code:
Env: SDK15, SES...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
The SDK 15.3.0 and 15.2.0 Documentation references ANT + BLE Serialization example in " \examples\connectivity\experimental_ant_ble ". In the SDK I only found " ble_connectivity...
Hello,
We are referring to demo project ( https://github.com/NordicPlayground/nrf52-ble-image-transfer-demo ). This is quite matching for our requirement. However we have...
What is the default state of the GPIOs after reset, until my code has a chance to configure them?
Are they all Input/HI-Z? Is there a place in the manual that specifies...
Mesh DFU works like:
if(fw_updated_event_is_for_me()) update_ and _relay(); else relay();
Is there a way to change this behaviour to:
if(fw_updated_event_is_for_me(...
Hi,
I'm working on porting a project from an NRF52840 to an NRF52832. Apparently I screwed up something somewhere and I can't compile the project anymore. I'm using GCC...
Hi,
I working on a project that need to communicate with other mcu by SPI, the communication is work, but I have question about the start and stop of communication.
...
Hi,
I just met some difficulties to implant more then one service into my project. The project was developed based on hid_keyboard.
The project can work normally when...
I am using 2 nrf52832 boards to talk to each other through UART. One is programmed to the central SDK example and other other is peripheral. In the code, i incorporated 2...
Hi, I got the issuse about the connection with nRF52810. I used nRF connect to connect the nRF52810 device via Android,but it isn't easy to connect successfully.The nRF log...
Hello,
I have a question about the nRF52840 device and the supporting documentation. I am trying to figure out the current ratings for the GPIO. On page 198 it states that...
Hello,
I have an issue with the function sd_flash_write which ends up in a hardfault when returning to the function calling it. I know there are many Q/A on hardfaults...
