I’ve got a bit of a hardware issue with the nRF52811 UART, receiving DMX data from a Chinese DMX controller.
Standard DMX data-rate is 250Kb/S, so the minimum bit time is...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
I am trying to keep nRF5340 in sleep state, and wake it up when there's a user input (e.g., button) and send a packet as fast as possible to iOS18. What would be the latency...
I have been following this tutorial by Nordic trying to install nrfConnect for VS Code, nRF Connect for VS Code, part 3: Building an application , but I am facing several...
Hi
I am using nrf70-wifi-ble-image-transfer-demo in the nRF7002 DK.
I deleted all the mega camera stuff as I want the MCU read image from another stm32, I successfully...
Hello,
We are developing a system that have the nRF5340 as a part of several MCUs, and we want to be able to upgrade both cores.
According to this: DFU for the nRF5340...
Hi,
I am developing an application using the nRF52840 as NCP with a raspberry pi as the primary processor, using wpantund. I have 3 devices (3 raspberry, each with its own...
In most of the examples the FIRST_CONN_PARAMS_UPDATE_DELAY define is set to something like 5000ms. Is there a reason it needs to be that long? I would like to switch to a...
Hi,
My question is quite easy. I need to use 36 or 38 (maybe something else frequency as well) kHz clock in our device. How it is possible or is this possible at all ? I...
Hello All
Since 3 days now, I am trying to program my third party beacon board PTR9048 with the PCA10028. I'm pretty sure, that I connected it correctly, because I can...
Can the
sd_ble_opt_set
function be used to set a default channel map in the central role prior to any connection requests to advertising peripherals being...
Hello,
I am using nRF52840 with nRF5_SDK_15.0.0_a53641a.
I am looking at the QSPI example which I have slightly modified so that after the write of 256 bytes, it enters...
Hello I just got nrf52dk board, and have issues with dfu mode of MCU, after power on board is dead no any lights, no USB connection. After pushing reset and power on, MCU...
Hello,
I am implementing an application, where I want to connect three NUS peripherals to one NUS client. As a beginning point, I started with the supplied examples from...
I have ported the keyboard example code and integrated it with another set of services. However I don't see the device responding to an LL_ENC_REQ. I'm not sure what I can...
This probably falls under the category of BLE Basics, but I'm a bit slow and need some help. Here's my scenario:
I'm building a very simple BLE Peripheral that provides...
I'm currently using nrf8001 to send data to my phone. To save power from the peripheral device, I wanted to change the connection parameters.
I set the min and max connection...
Hi, I'm using nRF52832 with my external board.
I'm recently working ble uart example.
I control motions with tx message such as LED, motor and so on.
Now, I want to...
Hi,
I need to set a client back to the state, when its flash was erased and programed, so if I understand this correctly, the provisioning data has to be erased.
How could...
I've been developing on the PCA10028 development kit with print statements working fine (though at the moment it seems only SEGGER_RTT print statements are working and not...
