This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
I downloaded the Android App from https://github.com/NordicPlayground/Android-nRF-UART, and when I run it on my phone it does not see ANY bluetooth devices. However, when...
Given that mbed is based on RTX, has anyone used the nRF5 SDK with mbed or know if it would be an easy or seamless integration ?
Thanks for your help!
Mickael
I'm implementing Capacitive Touch sensor using comparator method.
The hardware configuration was followed exactly as described here .
The output differs depending on the...
Hi,
I tried to make a special application that includes 3 advertisements, (one with softdevice, and two others with timeslot), then i successed to
integrate all the three...
Hi There,
I'm a beginner with Nordic products and I'm taking over the nRF52840 Preview Development Kit.
My final goal is to supply with a solar cell my nRF52840 running...
Hi,
We have issues with mBed's Thread::wait() in mBed 5.7.2, which causes our interrupts to stop working. Below is a small example that can be used to test this. By removing...
Hi. In the product I'm working there is a qi and NFC antenna on the same side. I resolved the issue of the qi charger overloading the nRF by placing a 1nF capacitor in series...
I enabled whitelist in my nrf51822 device and get my phone irk address after bonding then i hardcode that specific irk to my nrf device. Now i can only able to connect my...
I am using KDeveloper to program the nRF52, so far it has been working fine, but I want to be able ofdebugging and going into breakpoints, etc. What should I set in order...
I have programmed two boards(pca10056) with the cli example in thread sdk.I have set the first one as the leader and the second as the child but after pinging the kit the...
Hi guys,
I am working on a nrF52832 project and want to use Segger Embedded Studio since there is a license agreement for nordic based projects.
I am using freertos from...
Is it possible to communicate between 2 Nordic kits at 1 M baud without HW flow control? I came across this post in the forum which states that bytes can be missed when switching...
I am trying to use gcc to compile a c++ code for nRF52. I am using the TWI library and am getting the error below. Can anyone help me rewriting this macro so that it compiles...
Hello All,
I am using 32 pin nRF52810 chipset.
Crystal have two pin and it will work as in sch. (Xin and Xo)
when using Osc (which is an external clock generator) there...
