Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
I am working through the heart rate monitor central ble device code on Nordic SDK 8.1. I noticed that the variable
bool m_memory_access_in_progress = false; /**< Flag to...
I'm wondering whether or not we can make a specific BLE peripheral device with having this ability to be supported by client iOS/Android device for automatic scanning/reconnecting...
Hello everyone,
Recently I've had problems with using JLinkExe directly from the Linux terminal. I finally decided to give nrfjprog a try. It worked, I can finally type...
I develop a nrf_mesh application.
I can send a mesh packet by nrf_mesh_packet_send().
But I can not receive a mesh packet.
(I can receive a advertise packet by nrf_mesh_rx_cb_set...
I am developing an app that uses both a central and a peripheral device using Nordic SDK 8.1. I was working off the hrm example code and wanted to move all the scanning methods...
Hello all. I am a beginner with nRF and am trying to get the Eddystone example (titled "experimental_ble_app_eddystone" in the examples folder) to work. I have opened the...
Hi,
I am working with the BLE Nano module and the mbed online compiler. I have the Nano acting as an SPI slave. The problem occurs when I try to add BLE functionality....
I've spent some time searching and haven't found a definitive answer or anything obvious in the code. I'm developing the firmware for my application on the nRF52 DK, which...
Hello nordicers,
I'm stucked with long writes (android central to nrf52 peripheral)
I'm using SDK 12.3 and S132 v300. Android as the client central (RxAndroidBle libary...
Hello,
I ported nordic heart rate example to nuttx. I have peer_manager_init() in my codes.
After programming the device, I can connect and bond when I issue "nrfjprog...
main.c I'm using S120 softdevice with nrf51822, I want to use S120 as central and peripheral devices.
When I received my beacon data then switch to peripheral for advertise...
Hi!
nRF52, SDK13, S132.
I work in central mode and need make
ble_nus_c_rx_notif_enable()
But in the code drivers I only have tx function. In a SDK9 for nRF51 I...
Hello,
I'm trying to prototype an application on the nRf52 DK (PCA10040) using the GCC toolchain. I followed all of the tutorial for setting things up and I can build and...
Hi all,
I tried to load the DFU example for nrf51822 from SDK12.3 on the dongle(PCA10000).
softdevice: S130 2.0.1
I followed the tutorial on: devzone.nordicsemi.com...
