Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
I am new to this forum and have some questions that I could not find elsewhere. The questions are:
Website asks me for a product key if I try to download the S210 soft...
Hi,
I was wondering whether bonding between devices is possible without using a passkey.
I found a good documentation by Nordic Semi which illustrates all the bonding...
Hi everybody
I've got a problem with my "custom hardware" with the "nRF51822 QFAAFA 1322AA" MC by Nordic. When I try to connect the hardware with the "Master Control Panel...
Hello,
I'm using GCC with the soft device 6.0.0. I'm having this reoccurring issue where sometimes I will start to debug and the execution flow will get stuck in some kind...
Hi,
I catched the air data packets by Sniffer and it shown that there was an error, MIC incorrect, which could be seen as followed, and the whole packet was malformed....
Hi!
I have some problem to reconnect an already bonded device containing a chip nRF8001 rev D with my iOS app. Rev C works fine with the first connection and the reconnection...
HI,
I want use some GPIO to detect "pin_high_to_low" or " pin_low_to_high".
and I think the "app_gpiote.c" might be helpful.
but I have been confused by function " sense_level_toggle...
Hi,
I'm starting to implement DFU using IAR's ARM workbench. In the example project for ARM that comes with the nrf51_sdk_v5_2_0_39364 SDK there is a file called bootloader_util_arm...
Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
I want to load a Blinky project to the AK board, and the dongle is used as a jlink, but I forget to move the jumper to the 'out', and the program is loaded to the dongle....
Hi,
I change the example ant_broadcast to acknowledge mode, but it seems that without a peripheral side,the LED0 will still twinkle.I don't know how to change the project...
Hi,
I'm porting a nrf51822 evaluation board 10001 tested application to a custom board. Part of the application is using UART interrupts to raise a flag and start data...
I am experiencing an error in the final linking stage of my build.
_build/blinky_gcc_xxaa_s120_xxaa.bin: file not recognized: File format not recognized
collect2.exe...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
