Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
Hi,
I've written a nRF51 SWD-JTAG programmer.
I want to enable it to check for minimum softdevice version and error out if a too-old softdevice is found.
It is easy...
I want to communicate four same devices with different hosts. i know that one host can communicate to seven devices and also a device is able to speak different hosts . i...
Thanks for the response. As a test, I loaded the same code onto a PCA10004 and it seems to work as you described. A breakpoint at 217 does get triggered when it receives data...
I have been perusing the source to micro-esb, and it appears that it wants exclusive access to the NRF_RADIO interrupt(RADIO_IRQHandler) and things are designed so that only...
Hi,
i need to save an array of 50 kB on the nrf51822 flash. I only need to read the data stored in the array. I come from the PIC micro world where i simply need to initialize...
Hi,
On peripheral side i have S110 device with ble_bas service and custom base service. Both have notifications.
On centrasl side is S130. After discovering services i enable...
I want to use the pca10001 to communicate as a master to an accelerometer, but when i use the function spi_master_open i get a NRF_ERROR_NOT_SUPPORTED error. I get no clock...
Hi everyone.
I am working with nRF51 to make two BLE device, One act as cetral and another as peripheral.
I have implemented almost functions that the two devices are...
Hi,
Do all NRF51822-DK (development kit) have the same silicon build revision? If not, which distributor should I approach for the latest revision and is there a specific...
I have encountered a problem with the IAR linker where I run into a 32k code-limitaion, even though I have a licence with no limitations. According to IAR, the problem may...
I was playing around with examples and decided to implement a custom service that sends the RSSI as a single-byte characteristic value. Here's the init function:
static...
Hi,
I'm trying to connect to BLE and send data on UART. I'm using nrf51422 with softdevice s310 and SDK v5.2.0.
The following code gives me error 3003 which I figured...
Hi,
I think getting started with the Nordic chips is not as easy as some others.
I would like to know what are the first things that I need to run my code on a Nordic? Especially...
I just got the nRFgo Dev Kit, and going through the set up I see I need a nRF6310 Motherboard, but I can't seem to find anything about it - like were to buy it.
