It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
I am trying to use Visual Code environment (on macosx Intel macbook pro) to program nrf52840 dongle.
The dongle is found and programmed with using nRF Connect for Desktop...
Hi Nordic，
One of my customer has a problem about 2M phy.
They use 52840 connected with IOS via 2M phy.
They set MIN_CONN_INTERVAL and MAX_CONN_INTERVAL both to 20...
Hi, I'm working on nRF9160 with Zephyr (SDK 1.7.1) and one SPI device. I analyze CS signal with correlation to SPI SCK. Is that normal that CS signal stays low much longer...
I am trying to add a Nordic Thingy 91 to my azure Iot hub.
i've configured the device according to the guide
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
I noticed when using the UART BLE Example that there is no password or pairing request to connect to and use the device.
Everything works fine, and I even implemented my...
I followed the official tutorial. The programmer 2.3.3 in nRF Connect for Desktop v3.10.0 in Linux has problems programming the nRF52840 USB dongle rev 2.1.0 in DFU mode....
Setup: Windows 10, nrfutil verison 6.1.3, python 3.10.2, nRF 5 SDK 17.0.2
I have a custom board running the stock DFU firmware from the nRF5 SDK. The only changes we made...
There are many questions on DevZone on modifications to NCS peripheral_uart/central_uart NUS example applications to support higher throughput.
We have been mostly successful...
I would like to use the nrf connect sdk to connect to a device and 'discover' the GATT services it supports, the characteristics in each service, and then read the descriptions...
Hi everyone!
I ported some project from NRFsdk 17.0.2 (all works fine) to Zephyr rtos and faced with issue - when set high speed uart (460800 - 921600) then some bytes ...
Hi All
A few times ago, I installed the nRF Connect for Desktop v.3.8.0 on my PC.
Getting started assistant, Programmer, Toolchain manager apps were installed and everything...
I want to know about following things:
1). NRF_SDH_BLE_GATT_MAX_MTU_SIZE
2). NRF_SDH_BLE_GAP_DATA_LENGTH
3). NRF_SDH_BLE_GAP_EVENT_LENGTH
4). Connection event length...
Hi There,
I facing one critical issue with softdevice, I cannot get it work in freertos environment.
Hardware: customized board based on PCA10056
SW: nRF5_SDK_15.2.0_9412b96...
HI
I am using the I2S on the nRF52840DK I have constructed an array and all works well except once I start it , it continues to run, I cant get it to play the sample just...
Hi,
In the product I developed, there is a UI flow about the mode of pairing and binding, which has a limitation that it can only be paired and bound when entering this...
