I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi all,
During development I've run into issues setting up a functioning characteristic notification for IOS or Android. The notification works fine using the NRF Connect...
This is the ticket:
https://devzone.nordicsemi.com/f/nordic-q-a/52310/how-to-switch-a-node-into-provisioning-configuration-mode-to-configure-with-nrfmesh-app-and-then-into...
Hello, we seem to be having an issue with LE privacy. We want to always use a random address when advertising, here is what I am seeing.
- SDK 15.3, Nrf52840.
If I disable...
Hi,
I'm working on enabling APP Protection while successfully executing below code:
if (!nrf_sdh_is_enabled()) { if (VERSION_BUILD <= MAX_RELEASE_BUILD) { NRF_UICR-...
Dear all,
I'm using and nRF51822 chip for implementing a wireless HID device with dongle.
The device has an RGB LED, and indication scenarios for different modes are played...
I'm using SDK 15.3.0 example twi_scanner with Segger Embedded Studio. I do a search entire solution for TWI_SCL_M and the only location it shows up is in main under the twi_master_init...
I'm having this issue with oldish SDK 12 but since I reproduce the issue with SDK 15: I re-used the code from https://devzone.nordicsemi.com/nordic/short-range-guides/b/software...
Hello,
I am using nRF5_SDK_15.2.0 and with s132_nrf52_6.0.0_softdevice
I am trying to interface with external Flash (MX25l64) using SPI.so when ever i am trying to send...
Hi
Any sample or known project that can transform nrf52 usb dongle and be driven through COM port?
Imagine a C program in Linux that opens the USB port where dongle...
Hi,
I'm developing a custom board based on nrf52. Currently, we are using Segger through J-Link to program nrf52 DK.
As for my custom board, I left a 2x3 pinout including...
As unicast address is a address of a element in a node.
We have to assign unicast address to 500 nodes each contains 2 elements, and we configured publish and subscribe...
Hello,
I am using nrf52832, having SDK 15.3.0 in Segger Studio IDE. Win10
I am using fds_test_find_and_delete() function, to find and delete particular record from flash...
I latest firmware and loaded and software thingy91_ltem_v0.2.2.hex. And I get reboot all the time. It was working when I first got the kit then when I was testing this weekend...
Firstly, I am a very beginner in the BLE domain. I have very little knowledge of it.
I want to do a project where multiple BLE peripheral devices(nRF52) will communicate...
Hello:
I have questions about eSIM card.
As we know, GSMA standard eSIM card is an empty chip, we can use eSIM card after ISP information is installed into eSIM card....
