[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
Hello,
We are currently developing a project based on the nRF52832 SoC, where two external sensors are connected:
Proximity Sensor: VCNL4040
Accelerometer: LIS2DH...
Hi
I was initially using Window 10 Laptop with nrf52832 ncs2.9.0 in visual studio code....I developed a ble application with mcuboot (over ble - reference nrf academy tutorials...
Hi,
1. The customer has two projects that both require the use of mcuboot. However, for these two projects, the source code and configuration of mcuboot need to be modified...
Hi, I'm working on a custom board with the nRF54L15 using NCS 3.2.1, and have configured spi21 on port 2 for a display. SPI pin configuration: SCK: P2.06 (TRACECLK) CS: P2...
I am working my way through the DevAcadmy (nRF Connect SDK Fundamentals) using an nRF52840 development kit.
In lesson 6, exercise 1, I try to get an I2C with a BME280 to...
In sdk-zephyr/samples/boards/nordic/battery/src/battery.c at main · nrfconnect/sdk-zephyr
nRF54L series doesn't have 'SAADC_CH_PSELP_PSELP_AnalogInput0', how should it be...
I am trying to interface an SD card over SPI on nRF54L15 using nRF Connect SDK .
I started from Nordic’s fs_sample , which by default uses SPIM20 on Port 1 pins , and this...
I am using SEGGER Embedded Studio v8.26 with J-Link software v8.94 on Windows (64-bit) for BLE development on the nRF52840 DK .
Using J-Link Commander , I am able to:
...
After upgrading my NCS version from 3.1.1 to 3.2.0 for the nRF54L15, I found that the GRTC resets after a sys_reboot(), whereas it didn't in the previous version. What changes...
Hello everyone. I'm using the nRF52840 Pro Micro board with the J-Link programmer and the nRF Connect extension for VS Code. This board comes with a U2F bootloader, but I...
I use a hardware timer to capture/compare incoming pulses using PPI to trigger the captures from GPIOTE. I previously wrote the same application for nRF52832 on the old SDK...
When running SLM on nrf91, it sends "Ready\r\n" over UART on boot/reset. On nrf54, we use "Ready" to detect reboots and rerun the setup. However, when the modem reboots, sometimes...
Hello Team,
I am using the nrf54l15 custom board for development. I have configured the P1.06 as a normal GPIO as follows:
And using it as follows:
The pin status...
I use example from nrf52 SDK. project path:nRF5 SDK\nRF5_SDK17.1\examples\ble_peripheral\ble_app_uart\pca10040e\s112\arm5_no_packs.
emulator: ST link V2
but no target...
Hello,
The nRF5340 supports audio transmission, while the nRF54L15 supports Channel Sounding. Is it possible to conduct audio transmission simultaneously with Channel Sounding...
