Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Dear friends,
I flashed a mesh serial example and fetched the Composition Datacomposition data by composition_data_get(), as below code:
I wonder the meaning about the...
I have implemented nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_beacon\pca10040\s132\arm5_no_packs code for iBEACON.
I am able to run it and able to see the advertised...
Hello,
I was using the send example which is located in C:\v1.5.1\zephyr\samples\drivers\lora and trying to send a message to an Arduino LoRa gateway.
However, I found...
Hello everyone,
I am stuck at a problem that I cannot resolve myself but I see that other people in the forum don't experience such a behaviour of their nrf52832s.
I want...
Hello,
I've been using SES for ARM (Nordic Edition) V4.16 (64-bit). I am working with nRF9160 sample code. While attempting to explore the code, when I right click on...
The program flow of the slave is to sample the analog signal source through the saadc and then send it to the host through the nus. When debugging on nrf52dk, configure the...
Hi,
In my main function, I just call a acceleration_read function to get data from the accelerometer sensor and call a NRF_LOG_INFO function.
But there're something wrong...
Hi,
I try sdk 17.02 nRF52840 usb audio demo,I want to achieve 48KHz stereo music play by a I2S DAC.
I finished adding DAC for I2S to play the sound data of USB Audio...
I am declaring the variable in one of the hardware drivers files that are provided by the nordic semiconductor. The variable is not static. The variable inside the function...
Are there any other QFN package baluns that we can use for NRF51822?
One suggested from STM is BGA, and I wanted to see if there are any recommended QFN baluns that we can...
Hi Nordic,
I have an NRF52805 board [ from Raytech] and I am implementing all my application using SDK v15.1.0.
As of now, I have implemented my application using the...
Hi,
We need to know rated output and gain of pcb antenna on nRF52 DK for a technical standards conformity certification.
Can you give us them and their evidence?
Thank...
I want to connect an LTE antenna to J1. However, the antenna has a normal male ufl connector - it appears not to fit.
Is an adaptor needed for this?
Thx for any suggestion...
Hi ,
my environment details:
nrf connect sdk
nrf5340 dk
segger embedded studio
I have seen I2C example code in below path
\v1.5.0\zephyr\samples\drivers\i2c_fujitsu_fram...
app_timer2.c from SDK v17.0.2 has a possible race condition in app_timer_start()
This calls the get_now() function which compares a "now" variable to a "m_stamp64" variable...
