Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
hello Nordic
i am working with nrf52840, sdk16, over the peripheral app_ble_blinky example
my system will go to sleep mode for 10 minutes each time, i wonder if there...
SDK: 4.1.0
Hi, I want to send change notification. so I writes below this.
Some buf_id has got failure in zb_zcl_ias_zone_set_status.
So I added loop which get...
Hi,
We are working on a board with nrf5340. We are running the nrf5340 in normal voltage mode. So, we have connected the VDD lines to 3.3V. Since we are using USB signals...
how can I put nrf52832 in the system on sleep mode on advertising timeout?
Currently, on timeout, the device is going in system off mode and restarting on interrupt.
Hello,
I noticed that you improved the hardware design in version 1.4. Is it still neccessary to use a bias tee for an external GPS? https://devzone.nordicsemi.com/f/nordic...
Hello, I am still learning about BLE devices and have a quick question regarding the Generic Access Profile. I understand that GAP defines 2 things:
The discoverability...
Per the notes on https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF9160-DK/Download#supl-c - "Highlight: Updated library made to work with the new modem library...
nRF52832 SDK 17.2
We are trying to get the packet loss/error information on a per channel basis. It is similar to what is being discussed in https://devzone.nordicsemi.com...
I am using NRF dongle in window PC and scanning tags with nRF connect->Bluetooth Low Energy . Is there any way to change the scanning parameters of nRF connect for windows...
Hi,
I have downloaded the nrf5 Sdk 17.02 from the website. And I have found the ble_gls example in ble peripheral example part.
Kit : nrf52832
1. Can you please explain...
Hi,
I am using SDK 17.0.2. I am using write and notification characteristics. There is a write and notification communication between iOS app and device. After successful...
I'm running into a problem where my softdevice is triggering the fault handler but only when I'm also using the USBD. The panic info is below, I've tried to double and triple...
I am working with signled door sesnor and it supports ZigBee 3.0 as it has an install code and mac address on the side of the sensor in the form of a QR code. When I run the...
We are using the latest pc-ble-driver with SoftDevice v6.1.1 and latest connectivity firmware on an nrf52832 (s132) which is connected via usb-uart.
We were previously using...
