Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
hi, i've used the official zephyr version till some days ago. the reset pin worked. now i've switched to the zephyr version "supported" by nordic and the pin reset isn't working...
I did the multilink central function when I used zephyr OS Connecting the five peripherals is stable at first, but after a while the error of <err> bt_att: ATT Timeout will...
Hi Everyone,
I have been developing with nrf52840 for quite sometime using Arduino. I would like to explore nrf5 Sdk for Zigbee and Thread because I want to use my nrf52840...
When I generate bootloader settings using nrfutil 6.1.0:
The output indicates the start address is 0x3fc00:
However, looking at the hex file, it contains identical...
I'm measuring the current of the following code:
I'm not using softdevices.
I have nothing more connected to the board than the power.
I measure about 0.320 uA which...
I'm trying to make a test app that includes sample code from GPS and udp examples.
Building for nRF9160DK with west.
Here's my Kconfig:
```
# # Copyright (c) 2020...
Please help me to eliminate the error : "cannot open source input file "nrf_erratas.h": No such file or directory" for nrf51422 for nrf 51(12.3) sdk in keil version 5
Hello, We noticed that when we enable the whitelist, we can successfully filter out connection requests, but not scan requests. Our device still responds to every scan request...
Hello sir / ma'am
I want to implement OTA with zephyr using openthread but the size of my code .bin file is too much like 412kB .
How can I reduce my code size ?
What...
Hello
I am building a code with Openthread (NCS V1.4.0) and the size of that generated Bin file is 405kB. I would like to know why size of that file is more? I need to reduced...
Hi!
We are working with the nrf5340 on a custom board and we are trying to reduce its power consumption to the minimum possible. We have a beacon advertisement application...
Hi all,
I have just some issues with sd_flash_write and sd_flash_page_erase functions. I have created some code to read the temperature value and save this value in memory...
Hi,
I am considering nRF52 (most likely nRF52833 or 811 ) for a new design - curious how mature is the concurrent multiprotocol support in nRF52 - in particular for nRF52833...
Hi All,
We are using nRF52840 MCU and SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71. We are designing a device that uses switches connected to the below pins,
Pin...
Hi,
I use a custom board, softdevice and boot loader.
I use DFU to update a slave chip firmware. Everything goes right until we invalidate and write flash :
// Invalidate...
