Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
hi
I connect AT24C02 EEPROM with nrf52dk.
I already test EEPROM with arduino and it work fine.
Now i want to communicate with NRF52DK kit,so which example I would prefer...
Hi Nordic.
I have an issue that I'm really stuck on. I am trying to send data from a radar sensor via your nRF52 DK BLE board. I've managed to make a working connection...
Hello,
we would like to use a nRF52DK for a simple bluetooth production testing as mentioned in AN34. If we are using an external 50R antenna on J1 do we need to cut the...
I am using nRF52832 SDK 15.2.
I would like to avoid using the 32.768kHz oscillator to save space and cost.
I am using BLE and sleep mode ON.
I defined in sdk_config...
If I build/flash from the command line with "west build -b nrf9160_pca10090ns" and "west flash -d build" it loads a fully combined image with mcuboot and (spm+application...
I am trying to write a program in C to have my central device(nRF52840 dongle) read the RSSI from a peripheral. I have never written C code before and was told to use:
TASKS_RSSISTART...
Hello, I am using nrf52832. My BLE device is slave device and its sending notification to master. I want to know if there is any feature to know if notification from particular...
Hi,
I am trying to read signal strength inside my code. At the moment I know I can do this with AT commands:
AT+CESQ +CESQ: 99,99,255,255,255, 46 OK
RSRP = -140 + 46...
Hi,
I am trying to develop a high speed application using the nRF51822 chipset. As part of my application, I need to send at least 125 HID IN reports (each 20 bytes long...
Hello Nordic,
I'm developing app with nrf52840, SDK15.3.0 and s340.
The work almost has done, so we need to test ourdoor.
The problem is that we don't find out the...
Hey, I would like to connect the "image_transfer_demo" example (running on a nrf52840) with the "Nordic_UART_Service" (BLE central) example (running on another nrf52840)....
I am getting SAADC output on BLE device, but issue is I am getting hexadecimal output but i want decimal values.
I am not getting what to make changes. please suggest i...
Hi
We are doing some power optimizations. We are currently running the nrf52840 with REG0 as LDO, REGOUT0 to 2.1V and for REG1 the internal DCDC converter. As I see from...
Hello,
I am using the SDK 15.3.0 on nrf52832 DK evolution board, Segger Studio IDE.
Is there any issues with having the NFC tag extended a meter away from the PCB??
...
