here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
When we use nRF5 bootloader provided with SDK the first application flashing must always be done using DFU over-the-air. Only after that it is possible to re-flash application...
Hello,
I'm new to Nordic nRF52 and trying to send commands via termial to nRF52. After receiving commands, nRF52 will use these commands to do i2c communication with other...
Hi,
I'm trying to simply toggle a pin with GPIOTE out toggle task from RTC2 CC0 event. Wrote up the following code and checked the registers in system viewer. Everything...
I am using S132v2 on nrf52831. I am using UART BLE application. I want to turn ON BLE meaning advertising and all parameter of BLE whenever i press any switch. Also bluetooth...
Hi,
I know this question must get asked enough, but i am at my wits end and have not managed to find a solution for this yet.
calling sd_power_system_off returns NRF_INVALID_STATE...
Hi,
After couple minutes of running my application catch softdevice_fault_handler with program counter set to 0x11150. Can you tell me what may be a reason of this error...
Hello community,
We have a requirement to do concurrent BLE peripheral and broadcaster roles with S132 stack. This seems to be one approach but a bit crude for our requirement...
Hello,
while reading the nrf52840_OPS_v0.5, I discovered, that there is a 32MHz peripheral clock. I did not found any reference to it in the rest of the document. Is there...
Hello,
we need to first enable GPIOTE+IRQ. Then after 1st IRQ we want to keep only GPIOTE and disable IRQ. We do not want to disable GPIOTE (because it works with PPI), but...
I'm currently doing tutorials with the nRF52832 DK and am asking myself this question. How would I connect the nRF52 SoCs to my PC for flashing? Also, how should I edit the...
Hello,
I do migration from SDK11 to SDK12 (S132-SD-v2.0.1 to S132-SD-v3.1.0) and my device (nRF52-DK) randomly got a MAC of 00:00:00:00:00:00.
Helped by the migration...
Hi,
I am using BLE UART application with softdevice S132 on nrf52832 board.
I wrote a code where where i am using systick interrupt, GPIOTE interrupt. Also code has SPI0...
I have been reading device manager of SDK10.0 for nrf51822 . I looked at dm_ble_evt_handler and whole device manager source code but i didn't found where keys like IRK , LTK...
Hi,
i am working with nRF24LE1's as one master and many slaves. I also use the RTC2 functionality for the register retention mode.
As i read in the documentation the...
