Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Evaluating nRF53 PDK. Trying to build basic samples from zephyr repo as advised here - https://devzone.nordicsemi.com/f/nordic-q-a/54451/nrf5340-support-in-nrf-connect-sdk...
Hello,
maybe it is a very simple question but I didn't figured out the answer yet. Is it possible to start MCUboot from the application firmware code (to avoid pressing...
I have 20 advertisers. I have nrf sniffer hex flashed in one nrf dev kit and i am using wireshark.
I intend tht sniffer should scan only those device whose address i will...
Hey Everybody, I hope you guys find this Question in good health. I have a problem with #calender_example. When I run the Calendar example on original development kit, the...
Hello. Here's some information on my setup:
nRF Connect for Desktop v3.9.1 for Windows (Windows 10)
Toolchain Manager v0.10.1
Trying to download and install nRF Connect...
Hello
I developed a project based on the ble_thread_dyn_mtd_coap_cli_pca10056_s140 example (on the latest SDK version) with SEGGER Embeded Studio.
Now I would like to...
Hi Nordic,
how can i use the QWR module on the ble_nus_uart peripheral example? In the example we use nrf_ble_qwr_init() to initialize the module but i don't get the effect...
Hi,
im testing the Matter template example from Framework 1.8, with the prebuild chip-device-ctrl from github releases.
After provisioning the device as described in https...
This is in reference to the note in the manual that says:
6.14.11 Battery protection If the antenna is exposed to a strong NFC field, current may flow in the opposite direction...
I can not get the SPI Slave function working on nRF52840 (nrf52840dk_nrf52840 board)
In the nrf52840dk_nrf52840.overlay I wrote: &spi1 { compatible = "nordic,nrf-spi"; label...
I have a number of devices that currently have an S132 softdevice, USB enabled DFU bootloader and application.
I am intending on updating the application, which removes...
Hi
I am now trying to add the light lightness model to the light switch sample code in order to use both the light switch and light light lightness features.
After adding...
I am using nrf sdk v_17.0.2 soft device s132
my query is for connected mode.
My project uses nrf52832 SoC, SHT4 temperature humidity sensor, 2MB flash memory.
it advertise...
Hi everyone, I’d like to build native code on my Arduino Nano 33 BLE on a Mac, i.e. using the nRF Connected SDK and avoiding the Arduino Core/Mbed OS. I’ve followed zephyr...
Hi All,
I have successfully used notify to transfer 1 byte of data.
Now I want to try to transfer 1 array but I have a problem as shown in the figure.
Here is my...
