Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I request detail information about the UART internal implementation of the UART in the nRF52810 microcontroller.
Many application are used in noisy environment.
From other...
Hi
I am trying to flash the device with the bootloader, the soft device and the application, because I do not want do the OTA update at production.
I used the following...
Hi,
I want to control leds of nrf 52840 board through raspberry pi 3 B model uisng python.
I used interactive pyaci example for provisioning nrf sdk board, but it requires...
I am using NRF52840 development board with SEGGER Embedded Studio (Nordic Edition)
I downloaded example code to target board. The software run with Zephry. I found function...
I tried to follow this tutorial to set up the Connect SDK toolchain with CLion. It worked until I resetted the CMake Cache. Now it always gives me this error message.
...
Good evening,
I'm analyzing the FreeRTOS HRM example for PCA10040.
I'd like to understand the meaning of the following comment available in your code in order to prevent...
I am having a very strange problem with timers and the PPI channels.
I am trying to take a fixed number of ADC samples at 1 ms intervals starting at a fixed offset in time...
I'm trying to set up the nRF Connect SDK Toolchain on Ubuntu 20.04.2 LTS x86_64, following this manual.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.5.1/nrf/gs_installing...
I have plugged in the NF5340 development board into a USB port on my laptop with a USB 2 cable, but LED 1 does not light. Only the LED next to the light PCA i.c. lights -...
Hello,
I am using nRF Connect for Descktop for Windows 10 v3.6.1, and the nrf52840 Dongle.
Is it possible to scan / connect to BLE 5.0 devices (with PHY Coded) using...
Hello,
I'm working with nRF52840 dongle, i installed nRF Connect on ubunto 18.4 and i am using python3. After installling pc-ble-driver version 0.15.0 in python3 i tried...
I start the sniff and see packets from all advertising peripherals in the area. I select my peripheral in the Device dropdown list. Then I see a string of "ADV_IND" packets...
Hi there,
I've got a situation when using TWI where an ` NRF_ERROR_INVALID_ADDR` is returned having performed a call to ` nrfx_twim_tx`. I understand that this relates to...
Hi,
I have spend some hard time trying to figure how to work with RAM retention. Looks like it is working for me now, but now I retain all available memory. How much energy...
