I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi.
I am building my application on top of ble_app_uart__saadc_timer_driven__scan_mode example.
I want to interface an i2c device with it. The i2c device works perfectly...
Aim:- To read temperature and humidity over a mesh network and display it in an android application
Devices to be connected in Mesh :-
nRfF52840 Development Kit x2 ...
Hello,
I am currently working with nrf 52840, using segger embedded studio (V5.34) and SDK 17.0.2.
For some reason, when I open any example under ble_peripheral, such...
Hi,
I installed nRF Connect SDK v1.4.2 by the tool chain manager and was following the Getting Start guide and entered here.
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
I have two variants of the nrf9160 SIP one being the nRF9160 SICA B 0 A and the other being the nRF9160 SICA B 1 A.
When I use the AT%HWVERSION AT command on the B0...
Hi,
I want to write my own Multilink/UART example from scratch, because I'm too confused from all these examples.
What I need to get that code done? Or has anyone build...
I am trying to download the softdevice to the nRF52840 development kit using the nRFgo but:
1. On nFRgo I didn’t found the “Program softDevice tab”
2. Although the kit...
Hi
Migrating from NCS1.3.1 to NCS1.4.1, the Blinky sample stops working on my custom nrf5340 board. No compile error, but not running. I also have a nRF5340PDK. Works fine...
I want to use long range ble for advertising with nrf52833. I have a PCA10100 SDK board, and I'm running a program with type of BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_SCANNABLE_UNDIRECTED...
Hi!
So I've got one BLE Central and one BLE Peripheral that I should communicate. Ive based the Central code on nrf Connect SDK's "peripheral_gatt_dm" sample. First I...
Is there an existing implementation on how to do diversity (BLE) with dual antennas using nrf21450?
(could also be by using other antenna diversity switches / brands)
Hi! I'm trying to understand the possibility of doing a FW update to an empty NRF52810 chip via a host MCU running Linux. We have this setup on a custom PCB, whereas the host...
Hello,
I have two quick questions about the nRF24L01+ chip that I wasn't able to find from reading its datasheet.
1. Is the chip pre-programmed by Nordic or does it need...
