I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
There is an example in the SDK v15 folder. " ble_app_buttonless_dfu "
I write a custom firmware which has ble interface sending temperature data.
I want to add ble bootloader...
Hi,
I'm using the S132 v6.0 and SDK v15.0 to work with nRF52832. I found the it just get the advertising data. If the device put some data into the scan response, when I...
Hi,
I want to use nRF52840 USB dongle in my setup with other PCA10056 boards. I have seen that in link https://www.nordicsemi.com/eng/Products/nRF52840-Dongle it is mentioned...
Need to upgrade bootloader by application code. I have finished to program bootloader image to FLASH. Content is verified correct, comparing to SRC. However, the bootloader...
I have 2 52840 modules with PCB antenna and I am trying to check the max connection range
I followed the recommendations and achieved only 120m.
I cannot use the examples...
Hi, we recently using audio with ATVV service instead of HID service. As we notice, Audio would enable by SR3 itself in ATVV service if we push the key, but not in HID service...
Hi Nordic:
I want to change TX power of mesh-sdk.2.1.1 light switch, I've follow
https://devzone.nordicsemi.com/f/nordic-q-a/34491/mesh-range-power-and-mode
and set...
Hi,
I have bougth one Nordic Thingy 52 and one nRF52840-DK. My idea is to communicate both via bluetotth.
For example, i want to capture the temperature adquired by Nordic...
Hi guys,
I am using the softdevice S120 firmware: s120_nrf51822_1.0.0-1.alpha_softdevice.hex
The error_handler registered when calling sd_softdevice_enable is called...
We are implementing a Nordic NFR52832 using the ARM mbed ble stack that leverages the Nordic SDK using a HID over GATT profile. Windows 10 seems to have an issue with this...
Hi all.
I'm trying to make a list of brands and models of Android phones that have implemented LESC. I appreciate any feedback and experiences working with LESC (numeric...
Hi There,
I just want to confirm which method is being used to perform DFU over thread (Single bank update or dual bank update), and can I perform DFU on Sleepy end device...
Hi,
I'm trying connect NRF 52840 width Intel AC 9260 Windows 10 Desktop/
When I compile and run any examples from nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral and I...
Hi,
when generating settings on windows using nrfutil on one project takes about 2 minutes and it swallows whole memory during the command.
The command i am using is:...
Hello,
I am trying to use nrf5280dk with RIOT OS and Contiki OS. I am following these steps to enable access to the device from os. https://devzone.nordicsemi.com/b/blog...
